搜索资源列表
es_mutil_meters_with_m128
- 基于MEGA128的多功能仪器,提供以下9种功能： 1. 2路0-10 VDC 电压表 2. 1路0-30V DC 电压表，带有一个10X跳针，可以测试0-300VDC 3. 0 – 3 安电流表 4. 4 通道逻辑分析仪 5. 频率发生器，50%占空比方波，0－5VDC，1HZ到8MHZ. 6. 波形发生器，正弦波、三角波、方波，1HZ 到 20＋MHZ? 7. 频率计 8. +5 VDC ，200 mA
sin-lookup-table
- 基于嵌入式的正弦查表程序.在sintable.asm中定义的正弦表.系统频率设置49.152MHz，强振模式.-based embedded sine chat program. Sintable.asm defined in the sine table. System set the frequency 49.152 MHz, strong vibration mode.
Dac12_3
- MSP430F1610 generates a sine wave from a look up table using timer interrupt.
通过DA转换查表实现正弦波输出
- 通过DA转换查表实现正弦波输出，无法调节周期,DA conversion look-up table to achieve through the sine wave output, can not adjust the cycle
signalproductProtues.rar
- 简易信号发生器+Protues仿真,函数波形发生器产生波形表，通过DA转换产生正弦波。,Simple Signal Generator+ Protues simulation, waveform function generator waveform table, have a sine wave through the DA converter.
VsinTab正弦波表生成器
- 单片机产生正弦波一般采用查表的方法，该软件能够产生8位和12的DA的表值，对单片机开发人员来说很方便。-Single-chip generally have a sine wave look-up table method, the software can produce 8-bit and 12 of the DA' s table value for developers of single-chip easily.
timer
- DSP5502的定时器发生器部分，从内存中读正弦表，然后向通用引脚发数，测得是好用的 -DSP5502 timer generator parts, reading from memory sine table, and then to pin the number of GM, is a useful measurement
SinewaveCodeGenerationProcess
- 正弦波代码生成程序,用来生成单片机等做正弦波产生时的代码表！-Sinusoidal code generation process, used to generate single-chip generated sine wave and so on to do when the code table!
sin51
- 51单片机产生正弦波 下列数据是我计算出来的正弦函数在0~90度区间的数值（0~128），可以用于8位DA输出，把这个数据表存 进去查表就行了，其他角度做点儿简单的计算就行了。-51 single-chip generated sine wave data is the following, I calculated the sine function in the 0 ~ 90 degrees of numerical range (0 ~ 128), can be used for
sin
- 在51单片机中实现正弦波的发生。采用查表的方法实现。产生5HZ的正弦波。-51 SCM in place to implement a sine wave. Achieved using look-up table method. Sine wave generated 5HZ.
C_and_Matlab_voice_output_c8051f330_DAC
- 利用C8051f330的DAC范例程序，实现语音输出；demo源程序做了小小的改动，再把语音数据填入原来的正弦表格；语音数据来源于wav文件，Matlab重新采样转换为C语言的0x**格式，导入TXT文件；ps:这个程序在我的baidu空间也有；huxuec-20101024-The DAC sample programs using C8051f330, voice output demo source code to do a minor change, then the sine of
sin_wave
- 单片机正弦波码表生成软件 内含程序代码 测试以通过-SCM software includes sine wave generated code table to pass the test program code
sin
- 功能简介： 这是一个通过读取正弦波表产生正弦波的小程序。最简单的验证方法即为：可以将DAC OUT端子的2号脚连接一个5~15K的电阻到地，通过示波器即可观察到正弦波。当然也可以采用DAC0832数据手册中的电压输出型接法进行实验。-Features: This is a sine wave generated by reading the table of sine wave applet. The simplest method of authentication is:
Sine-function-table
- 正弦函数表，在单片机输出正弦波形时可以加以引用-Sine function table, the microcontroller output sine wave can be referenced
51zhengxian
- 51单片机，利用正弦表发正弦波程序，本例幅值最大2.5v，频率5HZ，另附正弦表程序，可以根据需要更改幅值和频率-51 SCM, sine table made sine wave program, in this case the amplitude of the largest 2.5v frequency 5HZ attached sine table program, you can change the amplitude and frequency ...
Signal-waveform-generator
- 信号波形发生器，内附proteus仿真工程及VsinTab正弦波表生成器-Signal waveform generator included proteus simulation the engineering and VsinTab sine wave table generator
chabiaozhengxianbo
- 通过建立一个表格，将正弦波的点阵存起来，然后通过IO口将一个个数送给液晶屏显示。通过该过程能将正弦波无失真显示出来。-Through the establishment of a table, the lattice of the sine wave is kept up, and then through the IO port a number sent to the LCD display.
STC15W4KxxS-output-SPWM
- 用STC15W4KxxS4系列单片机输出两路互补的SPWM，带头文件及excel正弦波表计算。-STC15W4KxxS4 series microcontroller output with two complementary SPWM, lead and excel file to calculate sine table.
STC15-SPWM
- STC15单片机的输出SPWM波，带头文件，还有正弦表数值计算表，直接计算替换代码相应部分即可实现自己的点数、频率、占空比控制。-STC15 microcontroller output SPWM wave, lead documents, as well as the sine table numerical table, replace the code directly calculate the corresponding portion of their points can be r
SPWM
- spwm正弦表有很多，但不知怎样调用它，有了这个脉宽计算器 直接调用，不同的定时器频率生成不同的spwm 还附带有定时器周期设置计算值，对正弦波开发很有帮助 (SPWM sine table has a lot of, but I do not know what to call it, the pulse width calculator direct calls, timer frequency of different generation of the SPWM also comes w