搜索资源列表
软件UART示例
- 利用c8051f020单片机进行串口通讯的软件程序，此型单片机将会成为8位机主流-by Using C8051f020 MCU for serial communication software program, this type of SCM will become mainstream eight -
15F104E_UART
- STC15F104E单片机用定时器T1做软串口-STC15F104E SCM software to do with the timer T1 serial
UART
- 软件模拟串口，实现多串口的源代码，完整可编译直接应用。对于单片机只有一个串口的进行扩展-Simulation software serial, serial multi-source code, complete the application can be compiled directly. For there is only one single-chip serial expansion
NO1
- 用MSP430F5438定时器TA软件模拟UART,实现半双工通信-MSP430F5438 Timer TA software simulation UART, to achieve half-duplex communication
ME008-UART
- MSP430使用UART与PC通信，需要使用串口调试软件-MSP430 and PC using the UART communication, need to use serial debugging software
UART
- 单片机开赴小软件计算波特率只需输入所需波特率技能得到设置字取值-Moved to a small single-chip baud rate calculation software Simply enter your desired baud rate setting skills word values
WLW-Uart-070522
- 沃尔沃原车DVD触摸屏协议转换软件,用于加装导航的协议转换.-Volvo original car DVD touch-screen protocol conversion software for the installation of navigation of the protocol conversion.
Dual-uart
- Silicon 8051F310双串口模拟程序源代码-Silicon 8051F310 dual serial simulation program source code
Extend_Uart
- 一般单片机只有Uart0和Uart1两个串口，在实际工程中，可能会用到3个或以上的串口，该资料介绍如何实现软件Uart-General Singlechip only two serial ports UART0 and Uart1, in practical engineering, may be used three or more serial ports, the information on how to achieve software UART
software-uart
- 软件UART程序，用PCA做波特率发生器，使用的是C8051F000单片机-Software UART procedure, PCA to do with the baud rate generator, using a single-chip C8051F000
UART_pic
- 使用PIC的UART硬件接口进行通信，程序在PROTEUS仿真软件上成功运行-use PIC microcontroller to comunicate with UART interface,the program has been sucessfully run in PROTEUS software
uart
- 采用软件方法来实现单片机的通用串口引脚来模拟UART。根据要求采用P1.0作为发送端（TXD）,P1.1做为数据接受端（RXD），并采用全双工通信模式。由于MAX232电平转换芯片除了做UART的几个引脚后，还剩余T2IN,T2OUT,R2IN,R2OUT.所以采用模仿UART的接法.每次通信，发送的数据加1，接收的数据加2.用51系列单片机。-The use of software methods to achieve single-chip Universal Serial pin to s
uart
- 这是一个串行通信接口的实例就是在单片机时钟频率在12MHz 波特率 9600bps 的通信方式下实现软件UART的发送程序。 -This is an example of serial communication interface is a single chip at 12MHz clock frequency in the communication baud rate of 9600bps software UART implementation of the send proces
c8051f-UART
- 本应用笔记讨论基于C8051Fxxx系列器件的软件UART实现方法本文给出两个完整的例子一个用PCA为波特率发生器的C语言程序和一个用定时器0为波特率发生器的汇编语言程序-Application Notes discuss the C8051Fxxx series of devices based on the software UART implementation integrity of this paper two examples of a baud rate generator wi
AN115SW
- 同过PCA实现的软串口程序！本人测试过，不占用额外的CPU资源。-SOFTWARE UART EXAMPLES
IO_SOFT_UART_USE_TIMER
- C51很好的IO模拟串口程序，也称软件UART。只需用一个定时器，实现中断接收。程序编写得很规范，有很多个晶振频率和串口频率可选。是一个比较好的软件串口程序。-C51 a good simulation of serial IO program, also known as the software UART. Just use a timer to achieve interrupt reception. Programming very standardized, there are man
uarts
- Generic software uart written in C
PT22726
- For this project you need a 3.7v power supply that prepared by LM317 regulator. So you need MAX232 for connect uart to pc .my AVR chip project is Mega8 that you can program on any Avr chip have 2kbyte rom. In bascom spi hardware don’t work correct, s
MSP430F149--NRF24L01
- MSP430F149驱动NRF24L01程序-MSP430F149 software use to drive NRF24L01
UART
- 一些mcu(微处理器)没有硬件异步串行口（UART）为了组网，只能用软件模拟 异步串行口（UART）-Some mcu (microprocessor) no hardware asynchronous serial port (UART) for networking, can only simulate asynchronous serial port software (UART)