搜索资源列表
DS18B20
- 利用89S51单片机，通过DS18B20温度传感器测得当前的温度值，再送入4位8段数码管显示-Using 89S51 microcontroller, temperature sensor, through DS18B20 measured current temperature value, and then into four 8 digital tube display
AT89S51+DS18B20+LED
- AT89S51控制DS18B20进行温度测量，用三段LED进行显示，伟福仿真成功-AT89S51 control DS18B20 temperature measurement, using three-LED display, Wei Fu successful simulation
ds18b20
- ds18b20实验，利用51单片机控制18b20实现温度控制，从而实现温度计的效果。-DS18B20 experiment, using 51 single-chip control 18b20 achieve temperature control, and thus achieve the effect of the thermometer.
DS18B20
- DS18B20最全驱动.包含CRC8算法.ROM Search等.主机采用AVR mega16或者mega32.原创作品.-DS18B20 most drivers. CRC8 algorithm contains. ROM Search and so on. Mainframe using AVR mega16 or mega32. Original works.
DS18B20
- DS18B20温度采集和输出显示程序，用汇编语言实现-DS18B20 temperature acquisition and display program output, using assembly language to achieve
ds18b20
- 18b20程序代码，及数码管显示，74ls164-the way of using ds18b20
DS12C887-DS18B20
- 该程序可实现：以AT89S52单片机为核心，采用实时时钟芯片DS12C887计时和液晶1602作为显示输出，实现了多功能时钟。加入了DS18B20传感器，使时钟还增加了温度显示的功能。-The program can be realized: The AT89S52 microcontroller as the core, using real-time clock chip DS12C887 and liquid crystal display output 1602, as to reali
ds18b20
- 以MCS51单片机为例，采用寄生电源供电方式， P1 1口接单线总线为保证在有效的DS18B20时钟周期内提供足够的电流，可用一个MOSFET管和89C51的P1 0来完成对总线的上拉，当DS18B20处于写存储器操作和温度A/D变换操作时，总线上必须有强的上拉，上拉开启时间最大为10 μs。采用寄生电源供电方式是VDD和GND端均接地。-To MCS51 microcontroller, for example, using parasite power supply mode, P1 1 K
DS18B20
- 18B20测温,用键盘控制, 18B20测温,用键盘控制, 18B20测温,用键盘控18B20测温-18B20 temperature, using the keyboard control, 18B20 temperature, using the keyboard control, 18B20 temperature, using the keyboard control, 18B20 temperature
DS18B20
- 用DS18B20温度传感器与单片机，构成温度计的程序，有读取与显示组成。-Using DS18B20 Temperature Sensor and constitute a thermometer procedures, read and display component.
DS18B20(MSP430)
- 利用但总线DS18B20测温程序，并在LCD显示，取三位有效小数位。整数部分两位。共5位显示。 可在利尔达MSP430F449开发板上直接实现功能。-However, temperature measurement procedure using the bus DS18B20 and LCD display, taking three decimal places effectively. Integral part of the two. A total of five shows. L
ds18b20
- msp430f149读写ds18b20的程序-temperature measurement using dsb18b20 running on the msp430
mega16-DS18B20-1602lcd
- mega16芯片编译的，利用ds18b20检测温度，并用lcd1602显示温度值-mega16 chip compiled using ds18b20 testing temperature, and display temperature values ??with lcd1602
ds18b20-lcd
- 基于51单片机的ds18b20温度传感器利用，c语言编程-Based on 51 single-chip temperature sensor using ds18b20, c programming language
ds18b20
- 用C语言编的一个数字温度报警器，可以显示温度，设置报警温度，超过报警温度的话二极管会闪，从而实现报警功能-C language code using a digital temperature alarm, you can display the temperature, set temperature alarm, over temperature alarm LED will flash the words, in order to achieve the alarm function
CC2530-DS18B20
- 这是基于CC2530的温度采集系统程序，采用DS18B20芯片-This is the CC2530-based temperature acquisition system, using DS18B20 chip
DS18B20-1602
- PIC16F877A 使用温度传感器DS18B20 根据DS18B20的读写时序，取得当前的温度值，并在1602液晶上显示出来-PIC16F877A using DS18B20 temperature sensor DS18B20 based on the read and write timing, get the current temperature value, and displayed on the LCD in 1602
DS18B20
- keil开发环境，基于LPC2138的温度显示，采用DS18B20温度传感器，LCD1602液晶显示，并附带PROTEUS仿真图-keil development environment, based on the LPC2138 temperature display, temperature sensor using DS18B20, LCD1602 LCD, and comes with PROTEUS simulation map
ds18b20
- 使用模块化编程思路，所有模块皆可独立使用（但是占用到系统硬件资源则需要改动）上机测试可行，使用ds18b20采集温度数据并且送至电机处改变其转速以及显示当前温度与转速等级。(The use of modular programming ideas, all modules can be used independently (but the use of hardware resources to the system need to be changed) test is feasible,
DS18B20
- 用ds18b20和atmega16单片机，仿真温度读取，DS18B20程序(Using DS18B20 and ATmega16 singlechip to simulate temperature reading, DS18B20 program)