搜索资源列表
embedded-system-functional-blocks
- 嵌入式系统构件光盘资料，Jean J. Labrosse写的按键、显示、串口等模块的接口实现。-Embedded system components CD-ROM, Jean J. Labrosse wrote buttons, display, serial interface and other modules.
STM32-serial-DEMO
- STM32 2个串口进行交互，串口1（2）发送的数据在串口2（1）接收并显示。-Interact of STM32 2 serial ports, serial ports (2) send data on the serial port 2 (1) to receive and display.
LPC2378Kit_PORT
- KEIL 下的UCOSII移植，里面有LED的点灯，点灯是需要按一下按LED灯亮一下，还有串口，不过波特率不准，只实现接收进入中断，其实就是完成了中断进入、信号量创建，对初学者十分有用。此例子用的是KEIL公司的MCB2300开发板，和英蓓特的LPC2300一样，原理图可以在KEIL公司官网上下到。-KEIL under UCOSII transplantation, there are LED
USART
- 使用ST标准库，加载uC/OS II,添加3个任务，通过串口输出CPU使用率的C源代码。CPU为STM32F103RBT6，串口为USART1-Using the ST standard library, add uC/OS II, add three missions, through the serial output of CPU utilization of C source code. CPU is STM32F103RBT6, serial for the USART1
KeyBoard-05
- LPC2200键盘代码，ucOS-II,周立功代码的扩展，串口传输，蜂鸣器，SPI等操作。-LPC2200 keyboard code
uCos2-20100609
- 友善之臂mini2440上的ucosii实例，支持串口打印和LCD显示的驱动。-An example of ucosii ,tested with mini2440, which supports serial printer and LCD display driver.
LPC1768-UCOSII
- LPC1768的UCOSII的移植模板，在ZLG模板基础上改的，ZLG的模板经过本人调试，好像中断里发信号量有问题。本人将其改正并在其中加了串口功能程序并调试通过，串口波特率设置为4800。-Template of LPC1768 with UCOSII run on it.The template of ZLG has some problems ,I correct all the problems and debug it .
sample2
- 基于STM32_V3.4固件函数库的uCOSII串口通讯实例-Based on STM32_V3. 4 firmware,function library,example of uCOS-II serial interface communication
PLC
- ucosII系统使用串口读取PLC控制器的信息；-read PLC data with uart on the ucosII system
LT-ARM214X-ucos
- 提取自力天电子的LT-ARM214X 开发板串口读写例程，是IAR环境在ucos系统操作串口，可以从里面提取ucos系统-The extract of Zili days electronic serial read and write routines of the LT-ARM214X development board, IAR environment in the ucos system operating serial port, can be extracted from the i
UCos-II.core.analysis.Transplantation.and.Driver.D
- 《uC/os-II 内核分析.移植与驱动程序开发》随书光盘中的全部源代码，全部通过调试。书中介绍μC/OS-Ⅱ的内核分析、移植过程和驱动程序开发方法。书中首先以μC/OS-Ⅱ在8051系列单片机上的移植为例子，详细剖析μC/OS-Ⅱ的内核和移植过程；然后以串口通信为例，介绍如何为μC/OS-Ⅱ实时内核添加设备的驱动程序；最后介绍μC/OS-Ⅱ在数字信号处理器[DSP]上的移植，以使读者进一步加深对μC/OS-Ⅱ的理解。 -" UC/os-II core analysis. Transpl
bsp
- 串口的缓冲区程序。32字节相当好用。环境：ucos-Serial buffer process. Very easy to use 32 bytes. Environment: ucosII
uCOS-II-LPC2214
- 这是将ucos ii成功移置到LPC2214上的源代码，并完成串口的相应通信。-This is the Source of uCOS-II about LPC2214.
uUCOOS_IICC51c
- uc/osii的c8051f移植的关键代码，我自己加入了串口与与一个定时器的移植汇编代码，对其他中断应用会有帮助 已通过测试。 -the key code of the uc/osii, c8051f transplantation, I joined the serial port and a timer transplant assembly code would be helpful to other interrupt application has been tested.
ucosiiuartintsend
- 基于ARM LM3S8962的UCOS II 程序。 运用UART中断进行串口发送的例程-ucos ii program based on ARM LM3S8962 communicate with PC according to UART int
canrx
- uart read ucosii,串口读写加驱动-uart read ucosii
ucosandlwipconvertlantocom
- 基于ucos和lwip实现网口和串口的模块实现，包括了软件架构和编程思路-LwIP uCOS and based on the realization of network and serial port of the module, including the software architecture and programming ideas
52223_ucosii
- ucosii在codefire系列的5222x上的移植，包括串口，定时器I/O的初始化程序等-ucosii in the 5222x series codefire the transplant, including the serial, timer I/O initialization procedures
uCOS_LPC2368Kit_UART
- 该代码是基于uCOS-II2.52下的LPC2368串口程序，在LPC2368开发板上调试通过，开发环境：keil mdk-The code is based on uCOS-II2.52 serial procedures under the LPC2368, LPC2368 development board in debugging passed, development environment: keil mdk
ff
- 高速串口驱动 源代码 移植到51系列单片机上的，经过测试无错误和警告-High-speed serial driver source code ported to the 51 series single-chip, tested error-free and warnings