搜索资源列表
uCOS51DOC_V2.0
- ok, -ok, ok,
uCOS2_C51_OK.rar
- C51 调试OK能跑起来的UC/OS2 ,C51 调试OK能跑起来的UC/OS2
uCos2-6410-u-boot-ok-now
- s3c6410下UCOS2操作系统的例程，在ADS环境下编译-s3c6410 operating system under the UCOS2 routines, compiled in the ADS environment
tinySH-uCOS-II
- 现成的工程，不需要修改，开源，用MDK411打开。硬件上只要有一个带USART1的STM32F10x的开发板，25M外部晶振，即可立即体验tinySH提供的便捷。 tinySH是运用于单片机上的命令行交互接口，方便系统调试与维护。 该接口类似linux的shell，有ls, cd, tree, exit, ps, reset, halt等命。不同的是，该接口不需要文件系统的支持，容量小。程序员可以在root目录下扩展目录与命令。 本人一直使用tinySH做产品开发。绝对OK！-Rea
LPC2200_uCOS-II
- 周立功开发板上的源码，呵呵，希望对你有用，我有着还行-ZLG source development board, Oh, want to be useful to you, I had still OK
UCOS_LM3S8962
- 裁剪过的 嵌入式UCOS 核心代码。要实现嵌入式操作系统，必须的！可以用在LM3S8962-ok
ucos_lpc2368soundcode
- 基于飞利浦的lpc2368的ucos的源码，如果要用到基于ucos操作系统的程序编写时，直接加载到ADS中去就ok了-Based on Philips lpc2368 of ucos the source, if the operating system to use to programming based on ucos when directly loaded into the ADS in the overhauled ok
ucosii-13K-ok
- 调试通过的基于STM32F103ZE的UCOS 2.86操作系统，5个任务切换-Debugging through the UCOS 2.86 STM32F103ZE based operating system, five task switching
UCOS
- 在8051中实现分时操作，架构已经写好了！只需在标记的地方添上你要执行的程序就OK了-Implement time-sharing operation in 8051, architecture has been written! Just add the tag where you want to run the program on the OK
UCOS_II_BANKED
- UCOS_II移植到xdt256和xs256，测试过，可以应用-UCOS_II transplanted to xdt256 and xs256, which has been tested. It is OK.
MCU-TEST
- uCos在STM32F105RB上的移植，测试完全OK~-uCos in STM32F105RB the transplant, tests complete OK ~
lcdos-OK
- 基于ucos2的简单程序，有利于初学者和自学者。因为是用keil4编写的，所以应该有用。-Simple procedure ucos2, conducive to beginners and self-learners. Is keil4 write, so it should be useful.
Source
- 华为EM323 UCOS驱动程序,已经测试通过-EM323 S DRIVER，test is ok
uCos2-6410-u-boot-ok-now
- OK6410开发板下移至的UCOS系统 包括对应硬件的驱动程序-OK6410 development board to move UCOS system includes corresponding hardware driver
C51_uCOS-II-200---OK
- ucos for ms51应用实例-时钟-ucos for ms51 application examples- clock
PROJECT-TEMP-BASED
- its temp cutoff sensor using atmega 8535. 4 pins of b port provide menu , ok up & down for setting cutoff. using l293d it uses relay to switch off any device and prevet over heating.
StepMoto_C
- 飞利浦步进电机驱动程序，测试可以运行-LPC ARM7 for MOto ,it run ok
uCOSPuCGUI
- stm32+ucosII 标准的代码 实验ok-failed to translate
OS_unSP
- 在SPCE061单片机上调试OK的ucos2内核代码-In SPCE061 chip debugging kernel code is OK ucos2
dsPIC33F764GP710A_ucos_demo
- dsPIC33FJ64GP710A，MPLAB X，C30 。官方无此单片机的ucos例程，我经过修改gld内存分配文件，ASM汇编文件，已经可以在dsPIC33FJ64GP710A上运行，并且添加了ECAN的汇编程序，ECAN已经可以使用。 初始化了一个task和一个队列。 可在此基础上实现更加复杂的功能。-dsPIC33FJ64GP710A ,MAPLAB X,C30,UCOS II ,ECAN OK,QUEUE DEMO