搜索资源列表
ENC28J60_Interrupt
- ENC28J60是一款串口通信的以太网芯片,速度可达到10M,体积小,引脚少,非常常用。-ENC28J60 Ethernet chip is a serial communication speed can reach 10M, small size, small pin, very common.
ENC28J60_Scan
- ENC28J60是一款串口通信的以太网芯片,速度可达到10M,体积小,引脚少,非常常用。-ENC28J60 Ethernet chip is a serial communication speed can reach 10M, small size, small pin, very common.
PID
- 可以利用CAP捕获输入引脚获得过零点,也可以利用捕获功能计算得到交流风扇的当前转速。-Can use the CAP to capture input pin for zero-crossing, the capture function can also be used to calculate the current speed AC fan.
TI-DSP-fengzhuang
- 这是一个TI系列DSP的全系列的芯片引脚封装库-This is a TI series DSP full series of chip pin packaging library
16.SCI
- TMS320F28335两个外部引脚:SCIRXD,SCI接收数据引脚;SCITXD,SCI发送数据引脚;2)通过对一个16位波特率选择寄存器的编程,可以得到64K不同的波特率;3)传输数据格式:一个起始位;1~8位编程数据长度;可供选择的偶/奇/非校验位;一个或两个结束位 -TMS320F28335 control sci rx and tx .
GPIOLed01
- 使用PWM1-PWM6引脚作为通用的I/O口来控制Basic2812上LED灯 -Use the PWM1-PWM6 pins as general-purpose I/O port to control Basic2812 on LED lights
dsp2407_spi_da
- 基于DSP2407的spi和da的应用例程,程序内有讲解,附引脚图。-Application of DSP2407 routines SPI and based on Da, procedures have to explain, with pin map.
CAP3-cesu
- 利用DSP2812的CAP3引脚测速,T法测速-Measurement of Rotating Speed
CORE_LED
- 该程序是针对ti的TMS320C6747新品的GPIO引脚的LED闪烁功能,在CCS环境下可实现,以及经过验证,可以执行。-The program is for TI TMS320C6747 new GPIO pin LED blinking function can be realized in the CCS environment has been verified, you can perform.
ADC7656
- 该程序是针对ti的TMS320C6747新品的GPIO引脚的LED闪烁功能,在CCS环境下可实现,以及经过验证,可以执行。-The program is for TI TMS320C6747 new GPIO pin LED blinking function can be realized in the CCS environment has been verified, you can perform.
DCMotor
- dsp 直流电机控制程序 通过设置McBSP各管脚的工作方式和状态,可以实现将它们当成通用I/O引脚使用-dsp DC motor control procedures of the pin by setting the McBSP and status of work, you can achieve them as a general-purpose I/O pin
Event-capture
- 利用事件管理器EVA中捕获单元的捕获输入引脚检测两个事件变化的时间。(通过手动时间开关存数值)-Using the Event Manager EVA unit captured two events capture input pin to detect changes in time. (By manually switching time value stored)
SCI-serial-communication
- 编程通过SCITXD和SCIRXD引脚以9600B每秒的波特率传送数据。设SCICCR置中的值,使SCI模块进行内部回送,即自发自收。-Programming through SCITXD and SCIRXD pin to 9600B baud per second data transfer. Let SCICCR set of values so that SCI module for internal loopback, ie spontaneous admi
SPI-serial-communication
- 利用2台DSP试验箱的SPI端口进行通信,编写程序通过一台DSP引脚JP2向另一台DSP实验箱传输数据,并储存到200H开始的连续存储区中-Use two sets DSP SPI port chamber communicates through a DSP programming JP2 pin test box to another DSP transmit data and save it to the beginning of a continuous 200H storage are
OMAP138
- 基于TI 的OMAPL138的设计 主要硬件 引脚分配-The design based on TI' s OMAPL138 major hardware pin assignments
1LED
- 采用dsp2812的复用引脚实现对外部led灯的控制-Pin multiplexing using dsp2812 achieve control of the external led lights
dds
- DDS IP核的使用说明,包括引脚说明和各种波形的仿真图比较-DDS IP core use, including pin descr iption and simulation of various waveforms comparison chart
Lab406-speaker
- 1.EMIF 接口 TMS320F28335DSP 的扩展存储器接口(EMIF)用来与大多数外围设备进行连接,典型应 用如连接片外扩展存储器等。这一接口提供地址连线、数据连线和一组控制线。ICETEK– F28335-A 将这些扩展线引到了板上的扩展插座上供扩展使用。 2.蜂鸣器由DSP 上EQEP1S 设置为通用I/O 管脚输出控制,可将此管脚上的频率输出转换 成声音输出。 控制的方法是使用 DSP 通用定时器设置EQEP1S 管脚以一定的频率改变高低状态,输 出方
LED
- F240闪灯程序利用XF引脚 delay延时-F240 flash program using XF pin delay delay
DSPCAPTUREtest
- // 该程序用于测试DSP的CAPTURE模块,由TIMER1的比较模块输出一个PWM 波形,此波形输入CAP4引脚,待CAP4捕捉该PWM的10次上升沿后,停止捕捉,并把10次捕捉值存于数组result[10]中-This program is used to test DSP CAPTURE.