搜索资源列表
AN1162SourceCodefordsPIC30F601
- 异步电机矢量控制,微芯DSP,例子程序,液晶显示,空间矢量调制,带转速编码器,Vector control of induction motor, micro-core DSP, example of the procedure, liquid crystal display, space vector modulation with speed encoder
PWM.rar
- TMS320LF2407A中实现PWM控制,从而控制直流电机的转向和转速,TMS320LF2407A to achieve PWM control of DC motors to control steering and speed
步进电机转速数码管显示
- 步进电机转速数码管显示,采用C51单片机控制-Stepper motor speed digital display, with C51 MCU
ch4
- PWM控制器,通过改变PWM占空比控制电机转速,调节节气门开度。-PWM controller, PWM duty cycle controlled by changing the motor speed to regulate the throttle opening.
Motor-PID-control-code
- 应用PID控制算法,以控制电机,对其转速进行控制来编程,电机转速采用霍尔编码器进行测量,应用DSP脉冲编码捕获功能对其信号进行采集,来检测当前电机转速。-Application of PID control algorithm to control the motor speed control to its programming, the motor speed encoder using Hall measurements, application of DSP pulse code ca
2812dsp-Sci
- 这是一个基于DSP2812的串口通讯下位机程序,通过该程序可以实现和上位机通讯,将上位机的数据读入,设置电机的转矩和转速.挺好的一个程序,供参考.-This is a serial communication based on the DSP2812-bit machine under the procedures, the adoption of the procedures can be achieved and the host computer communications, will
ex8_PWM
- 程序所在目录:ex_PWM 打开,进行如下操作: 1. Project->Open ,打开该目录中的工程文件。 2. Project->Rebuild ALL,编译链接 3. File->Load Program 4. Debug->Run 可以看到电机开始转动。本例程中PWM的频率是1KHZ ,输出的是两路带死去的PWM波形对。用户只需更改参数XPWM即可改变电机的转速和方向。该参数设置如下: XPWM=2400
ALL
- 用2407实现的通过电位器改变占空比,从而调节电机转速,并带有捕捉显示占空比-Implemented with the 2407 change in the duty cycle through the potentiometer to regulate motor speed and duty cycle with the capture display
Dcmotor
- 直流电机控制,可控制电机转速与方向,已在DSP实验箱上测试通过,希望对大家有帮助-DC motor control, can control the motor speed and direction, has been tested in the DSP test case passed, want to help everyone
2808plus
- 基于2808的带有按键显示的不同频率脉冲发生,以及输入输出信号,以及电机转速检测的代码-Based on 2808' s with the button to display the different frequency pulse, and the input and output signals, and motor speed detection code
DSP2812-Motor
- 利用DSP的PWM1和PWM2,然后经过了两级放大控制直流电机,若要改变电机转速或转向,可在DSP28_EV.c文件里按相应注释修改,即实现PWM波来控制电机。-Using DSP-PWM1 and PWM2, and then amplified through a two DC motor control, to change the motor speed, or steering, can DSP28_EV.c file comments by corresponding changes
PWMDJ
- 用DSP2407实现PWM控制直流电机的实验,可控制电机转速,调试通过-Achieved with the DSP2407 experimental PWM DC motor control, can control the motor speed, debugging through
SCIControlTest_DSP
- 该程序为串口控制电机转速的下位机程序。其上位机程序为SCIControlTest。 该程序为DSP2812所写。利用SCI1接收上位机的信号并反馈转速信号。同时利用pwm1来控制电机。其转速控制为单闭环PID控制,转速反馈通过QEP1来获得。-The program for the serial control motor speed of the lower computer program. The host computer program for SCIControlTest. Th
F2812-PID
- 1.掌握利用 ICETEK–F2812-A 评估板与ICETEK-CTR 板上带速度反馈的直流电机B 的 连接和控制原理。 2.熟悉F2812DSP 的通用IO 端口和定时器的编程使用。 3.学习利用数字PID 控制算法控制电机转速。-1. Master the use of ICETEK-F2812-A evaluation board and ICETEK-CTR-board DC motor with speed feedback and control theory B co
ELE
- 双馈电机变速恒频发电原理 通过对风力机转速的控制,可以实现最大功率点跟踪,尽量多地吸收风能;而调节无功功率可以控制向电网输出的功率因数,也可提高风电机组及电网系统的动、静态运行稳定性-VSCF doubly-fed electrical power through the principle of wind turbine speed control, maximum power point tracking can be achieved as much as possible to a
Capture
- 基于dsp2818,事件管理器捕捉脉冲序列并测量电机转速的dsp代码,c++语言编写-Based dsp2818, event manager to capture and measure the motor speed pulse sequence of dsp code, c++ language
Three-phase-brushless-DC-motor
- 三相无刷直流电机的控制程序,里面详细的介绍了控制电机转速,控制电机正反转的程序-Three-phase brushless DC motor control program, which detail the control of motor speed, reversing motor control program
ctrl-speed
- 上位机pc控制步进电机转速,可以用软硬件实现步进电机的启动和停止,可以采用上位机软件实现对步进电机转速的控制。-PC pc speed stepper motor control, stepper motor software and hardware can be used to start and stop, you can use PC software to control the stepper motor speed.
PI_PMSM
- 根据永磁同步电机数学模型建立的电机仿真模型,并使用PI控制器进行双环控制,达到调节永磁同步电机转速的目的。-According to the permanent magnet synchronous motor mathematic model of motor simulation model, and use the PI controller 2-ring control, to adjust the purpose of permanent magnet synchronous moto
EHABLDC20150321p_pzui_2
- 控制无刷直流电机转速,转速外环加电流内环(Control brushless DC motor speed)