搜索资源列表
led(7-1)
- DSPF2812学习程序：功能描述： 令6个贴片LED中的2、4、6点亮，1、3、5熄灭，适于初学者学习-DSPF2812 learning process: Function Descr iption: Order 6 SMD LED light in the 2,4,6, 1,3,5 off, suitable for beginners to learn
main
- dsp的流水灯实验，利用定时器及其中断，实现其亮灭，达到了解其时钟的目的-dsp of water Light experiments, using timers and interrupts, to achieve its light off, to understand the purpose of the clock
ADC
- freescale DSP 通过编写程序，在调节外接电位器的情况下，经过ADC的转换，控制LED有规律的亮灭。-freescale DSP through the preparation process, in the regulation of the case of an external potentiometer, after ADC conversion, control, regular LED light off.
EX08_Key4
- DSP 2812 通过按键来控制LED的亮灭程序 -DSP 2812 through the buttons to control the LED' s light off procedures
clock
- 基于DSP的数字模拟钟实现 左半屏显示模拟钟，右半屏显示数字钟，下方红绿灯 每1秒亮一位，实现循环彩灯效果。 通过键盘可该日期、星期和时间 具体实现方法是： 1.先按数字键选择要修改的数据位 （234567分别对应月日周时分秒） 2.按 + , - 对应的数据执行加1或减1-DSP-based digital and analog clock analog clock display to achieve left and right scr
Intersection-traffic-signal-control
- 设计一个紧急控制开关信号，当紧急开关信号为1时，两个方向的灯全为红灯。紧急开关撤消后，按照开关按下之前的状态继续运行（其参数要保存）。（2）设计一个夜间行车开关，当开关按下后，两个方向都只有黄灯闪烁，其它灯熄灭。（3）设计两个方向的亮时时间可调。-Design an emergency control switch signal, when the emergency switch signal is 1, the two directions of light are all red. Aft
F2812_LedFlash
- F2812 利用定时器CpuTimer0中断，实现LED亮1s，灭1s。 （CCS3.3开发环境下） 功 能：通过使用CPU定时器来控制LED D3的亮和灭 说 明：D3与引脚XF相连，XF为低电平时，D3亮；XF为高电平时，D3灭。频率为1Hz，即每隔1s钟，D3被点亮。间隔时间由CpuTimer0来控制。-F2812 using timer interrupt CpuTimer0, the LED light 1s, off 1s. Features: CPU timer to contro
c2
- 4个LED与pb6按键程序，pb6按下的0次，led全灭，1次，led2亮；2次，led3亮；3次，led4亮；4次，led5亮；5次，全灭。如此循环。-The of four LED pb6 key procedures, pb6 press 0, led all off, once, led2 light 2, led3 light 3, led4 light 4, led5 light five times, all off. So the cycle.
LED
- DSP2407控制流水灯的一个实例，采用实时检测按键的状态，进而确定LED的亮灭。-DSP2407 control the water lights one instance, real-time detection of key state, and thus determine the LED light off.
Led
- ICETEK-DM642-BR利用tms320dm642实现按键控制指示灯亮灭功能-ICETEK-DM642-BR use tms320dm642 button control indicator light off function
VMD642_led
- dsp板led灯控制程序。通过改变led灯寄存器的值，来控制等的亮灭。-The dsp board led lamp control procedures. By changing led lamps register value, to control the light off.
ExInt
- DSP28335的外部中断，可以控制LED灯的亮灭顺序-DSP28335 external interrupt, you can control the LED lights light off order
Key4
- DSP开发板上的8个LED发光管可以通过8个按键来使其点亮和熄灭。-DSP development board 8 LED light tubes can be turned on and off to make it through 8 keys.
source
- 本程序采用F2812作为控制器，实现6个小led灯一次亮灭，使用GPIOA0-A5输出口-The program uses F2812 as a controller, 6 small led lights to achieve a light off, use GPIOA0-A5 output port
redgreenled
- 红绿灯程序。红灯亮五秒后灭接着黄灯亮五秒，黄灯亮五秒后灭 绿灯亮五秒灭的同时，红灯亮五秒，依次循环-Traffic lights program. After five seconds the red light yellow light off and then five seconds, the yellow light green light off after five seconds off five seconds, while the red light five seconds,
GPIO_LED
- 用DSP的GPIO控制LED。设置GPIO的方式，数据传输方向，控制LED灯的点亮和熄灭。用延时程序实现流水灯。-With the DSP GPIO control LED. Set GPIO way data transfer direction, control the LED lights on and off. Delay program with light water.
3.2.4-cputimer
- DSP(TMS320F2812)系统定时器，主要通过定时器2实现两个LED的轮流亮灭状态。-DSP (TMS320F2812) system timer, Timer 2 is mainly realized through two LED light turns off state.
SourceCode08_Key4
- DSP2812上的键盘例程,键盘按下,IO口输入变低后,输出的IO口控制led亮灭,编译环境为CCS3.3-DSP2812 keyboard routines on the keyboard is pressed, IO port input goes low, the output of the IO population control led light off, the compiler environment CCS3.3
buttom-interrupt-to-LED
- 基于研旭DSP28335的开发板编写的按键13实现中断控制LED亮灭，对初学DSP中断有很好的帮助- Based on research Asahi DSP28335 Development Board prepared to achieve 13 key interrupt control LED light off, DSP interrupt for beginners have a good help
timer-to-LED1
- 基于研旭DSP28335基础版编写的例程，通过定时器控制LED1的亮灭，定时时间可调-Based on research Asahi DSP28335 Basic routines written by timer control LED1 light off, adjustable timing