搜索资源列表
swi_audio
- 通过DSP/BIOS设置SWI方式，进行codec的传输，实现音频传输-through DSP / BIOS setup SWI means, the codec of transmission, audio transmission
Docs
- 闻亭的TDS560USB PLUS仿真器的全部参考资料，用于配置CCS环境等-Wintech' s TDS560USB PLUS all the reference simulator, used to configure the CCS environment
CAN_RX
- F2812 CAN总线接收数据（CCS3.3开发环境下） 实验目的:通过外部其他CAN设备给Super2812发送数据，了解CAN总线的设置和通讯过程，请尤其注意ID的设置 实验说明:将MBOX16设置为接收模式，并采用中断的方式接收数据 实验结果:可以观察变量Rec_h，Rec_l,查看收到的数据-F2812 CAN-bus receiving data (CCS3.3 development environment) Purpose of the experiment:
Study-USB2.0
- DSP XDS510仿真器的驱动安装指南，pdf格式-How to setup the drivers of xds510 usb emulator
74HC573_www.ic37.com
- The SL74HC573 is identical in pinout to the LS/ALS573. The device inputs are compatible with standard CMOS outputs with pullup resistors, they are compatible with LS/ALSTTL outputs. These latches appear transparent to data (i.e., the outputs ch
epwm_deadband
- dsp28335 pwm dead time 設定程式-dsp28335 pwm dead time setup program
USB
- VC5416 对USB寄存器的读／写、配置； VC5416 对 USB的 FIFO 的操作； VC5416 对 USB的 setup 包的操作； VC5416 对 USB的 Endpointo 的操作；-VC5416 of USB register read/write, configuration VC5416 on the USB-FIFO operation VC5416 for USB operation of the setup packet VC5416
adc
- This example sets up the PLL in x10/2 mode, divides SYSCLKOUT by six to reach a 25Mhz HSPCLK (assuming a 30Mhz XCLKIN). The clock divider in the ADC is not used so that the ADC will see the 25Mhz on the HSPCLK. Interrupts are enabled and the EVA i
Example_2833xGpioSetup
- TO setup and enable GPIO
fb
- TI的DSP5410烧写FLASH芯片SST39VF400A的程序 包括寄存器的设置和FLASH操作的程序C代码-TI' s DSP5410 Shaoxie FLASH chip SST39VF400A register of procedures, including procedures for setup and operation of C code for FLASH
55_new_SDRAM
- 瑞泰开发板的SDRAM的设置程序，CE1，CE2分别设置，已测试，平台VC5509A-Skandia development board SDRAM' s setup program, CE1, CE2, respectively settings, have been tested, platform VC5509A
install_dsPIC_R2008a
- dsPIC6010A setup for PCs
DEC6416_USB
- 基于ti 6416芯片 程序包括 C6416 对USB 寄存器的读写，配置 以及FIFO，setup包 和 Endpoint（）的相关操作-Ti 6416 chipset-based procedures, including C6416 to read and write registers on the USB, configuration, and FIFO, setup package and Endpoint () of the related operations
Mcbsp_set
- TMS320C55x 的Mcbsp口设置-The setup of Mcbsp in TMS320C55x
15456468setmac
- DM365开发板的MAC物理地址设置程序，经过检测，直接可用-DM365 development board of the MAC physical address setup and test them directly available
ACI3_3_281x
- 这是一个基于281xDSP的三相感应电机的矢量控制的源程序，解压后内含一个安装程序，安装后的文件夹内包含了全部源程序及PDF格式的程序模块介绍。-This is a three-phase induction motor based 281xDSP vector control of the source, unpacked contains a setup program folder after installation contains all the source code and th
PMSM3_3_281x
- 这是一个基于281xDSP的三相永磁同步电机的矢量控制的源程序，解压安装后会有一个安装程序，安装后文件夹内含有全部源程序及PDF格式的程序代码模块介绍。-This is based on three-phase permanent magnet synchronous motor 281xDSP vector control of the source, extract the installation there will be a setup, installation folder and
GPIO
- DSP2407 GPIO设置例程代码 系统文件详细代码-DSP2407 GPIO setup routine code code system file details
spi_loopback2803X
- DSP2803X SPI设置程序，仿真可用-DSP2803X SPI setup, simulation can be used
cpu_timer2803X
- DSP2803X 定时器设置程序，仿真可用-DSP2803X timer setup, simulation can be used