搜索资源列表
example10 can 243 -2
- DSP 程序的测试 很有用的 仪器上面用的-DSP testing procedures very useful in the above apparatus
VHDL程序范例
- 这是有关VHDL的一些范例,可以通过范例学习一点东西,巩固自己学过的东西-This is the VHDL some examples, examples can learn something consolidate learned things
iic 用verilog语言写的FPGA iic驱动程序
- 用verilog语言写的FPGA iic驱动程序,实现对存储器的读写,有需要的可以下载看看哦!-Language used to write verilog FPGA iic driver to achieve the memory read and write, there is a need can be downloaded to see Oh!
Verilog.Verilog编写的出租车计价器程序
- Verilog编写的出租车计价器程序,可以设置按路程计价,按等待时间计价。非常方便,界面良好,Verilog program, prepared a taxi meter can be set according to distance pricing, valuation by waiting time. Very convenient, good interface
ds18b20.ds18b20的Verilog程序
- ds18b20的Verilog程序,经测试验证可以使用。注意此版本为DALLS DS18B20而不是DS1820,注意加5K上拉电阻。,ds18b20 the Verilog process can be used to verify by testing. Note that this version rather than DALLS DS18B20 for DS1820, the attention of Canadian 5K pull-up resistor.
FFT-IP.介绍了基于FPGA的FFT实现方法
- 介绍了基于FPGA的FFT实现方法,并给出了实例程序,程序通过验证,可以直接使用,FPGA based on the realization of the FFT method, and gives examples of procedures, procedures for the adoption of authentication, can be directly used
用verilog语言编写的按键控制流水灯实验程序
- 用verilog语言编写的按键控制流水灯实验程序。通过3个按键可以分别控制流水灯的亮灭、左移、右移。压缩包内也包含此按键控制流水灯实验程序的modelsim仿真文件。-Verilog language with control buttons light water experimental procedure. By three buttons can control the light water lights off, left, right. This archive also cont
labview波形发生和数据采集程序包含了很多子VI
- labview波形发生和数据采集程序包含了很多子VI,可以帮助大家学习-labview waveform generation and data acquisition program contains a number of sub-VI, can help you learn
脉宽测量程序源代码
- 脉宽测量:可以用来测量脉冲宽度,周期技术信号显示从00到FF,共16x16位,Pulse width measurement: can be used to measure pulse width, cycle technology signals from 00 to FF, a total of 16x16-bit
Chapter10
- 第十章的代码。 本书通过100多个模块实例,详细地讲解了Verilog HDL程序设计语言,全书共分13章,内容涉及VerilogHDL语言基本概念、建模、同步设计、异步设计、功能验证等,实例包括各种加法器/计数器、乘法器/除法器、编码器/译码器、状态机、SPIMaster Controller、I2C Master controller、CAN ProtocolController、Memory模块、JPEG图像压缩模块、加密模块、ATA控制器、8位RISC-CPU等及各个实例模块相
rs232
- fpga的串口读写程序,经硬件测试成功,波特率9600.可以改变分频值适应不同的时钟和波特率-fpga serial read and write procedures, by the hardware to test the success of 9600 baud rate. frequency value can be changed to adapt to a different clock and baud rate
VHDL_code
- 基于FPGA的AD,DA,LCD,LED,CAN,I2C,PS2,VGA以及一些通讯ASK,FSK等的VHDL源程序,所有程序已通过调试,需要的拿走。-FPGA-based AD, DA, LCD, LED, CAN, I2C, PS2, VGA, and some communications ASK, FSK, etc. VHDL source code, all procedures have been debugging, need to take.
div
- FPGA调试程序,测试程序,分频率。可以用于FPGA的初学使用-FPGA debugger, test procedures, sub-frequency. FPGA can be used for the beginner to use
8365samp
- ADS8365的源程序,可实现FPGA采集!-ADS8365' s source code, can be realized FPGA collection!
Chapter11-13
- 第十一章到第十三章的代码 本书通过100多个模块实例,详细地讲解了Verilog HDL程序设计语言,全书共分13章,内容涉及VerilogHDL语言基本概念、建模、同步设计、异步设计、功能验证等,实例包括各种加法器/计数器、乘法器/除法器、编码器/译码器、状态机、SPIMaster Controller、I2C Master controller、CAN ProtocolController、Memory模块、JPEG图像压缩模块、加密模块、ATA控制器、8位RISC-CPU等及各个
shuzizhong
- VHDL语言编写的数字钟的模拟程序,可以实现定时,时分秒的显示等-Digital clock written in VHDL simulation process can be achieved regularly, minutes and seconds of display time
uart
- verilog 语言,uart 测试程序,通过串口能够测试开发板上uart芯片的好坏-uart test module with verilog langunge,it can be used to test the uart ic on your board.
DNC12-test
- 128细分的步进电机驱动程序,有需要的朋友可以看看。-128 segments of the stepper motor driver, a friend in need can look at.
FPGA_can
- 实现基于FPGA的控制MCP2515发送的程序,本人编写通过测试,希望提供帮助-FPGA-based control program sent MCP2515, I write to pass the test, hoping to help
CAN驱动器-MCP2515-接口程序-Verilog
- CAN驱动器MCP2515驱动,verilog编写,实测可用(CAN driver MCP2515 driver, Verilog written, measured available)