搜索资源列表
uart from opencores
- 用VHDL实现串口 可以实现与pc机的通信 收发 中断都可以 效果比较好-VHDL implement serial port, it can communicate with pc, it can accept and send message, and it can be interrupted.
uart8.zip
- 使用Libero提供的异步通信IP核实现UART通信，并附带仿真程序。UART设置为1位开始位，8位数据位，1位停止位，无校验。且UART发送自带2级FIFO缓冲，占用FPGA面积很小。,Libero provided the use of asynchronous communication IP core implementation UART communications, and incidental simulation program. UART is set to 1 to sta
UART
- 自己实用Verilog编写的UART程序，1位开始位，8位数据位，1位停止位，本测试程序配置完管脚后，实用串口大师发送数据，则返回数据为发送数据+1-Verilog prepared their own UART practical procedures to start a bit, 8 data bits, 1 stop bit, the test procedure End pin configuration, the utility serial Master to send data,
Uart_Send
- UART的完整发送程序，包括完整的工程核源代码。-UART to send the complete procedure, including the complete source code of nuclear engineering.
uart
- verilog编写的uart发送和接收的源代码。简单易懂。-verilog uart prepared to send and receive the source code. Straightforward.
uart.vhd
- this modul is serial send & resive for RS232
uart
- uart send resive module
uart_txd
- 基于verilog hdl的UART串口发送子程序。-Verilog hdl a UART-based serial port to send subroutine.
my_uart_top
- 实现的功能如题，就是FPGA里实现从PC接收数据，然后把接收到的数据发回去。使用的是串口UART协议进行收发数据。上位机用的是老得掉牙的串口调试助手-To achieve the functions such as title, that is, to achieve FPGA receives data from the PC, and then receive data back fat. Using a UART serial port protocol to send and recei
s7enable_send0x55_UART_9600
- 最简单的UART发送程序，vhdl编写，系统时钟40M，波特率9600，外Load有效（一个高脉冲）即向PC发送一个字节0X-UART to send the simplest procedures, vhdl prepared, the system clock 40M, baud rate 9600, outside the Load effective (a high-pulse) to the PC sends a byte 0X55
uart_verilog
- UART Verilog，书中里的例子，绝对正确，用Verilog语言编写的串口通信例子-UART VerilogCommand Parsing NiosII serial serial parts, including the interruption, send the command prompt, receiving treatment and other characters. Spent a lot of hard work! Definitely useful for beginn
send
- 串口发送子程序verilog 串口发送子程序verilog -uart send verilog
UART
- VHDL语言写的串口发送、接收程序，根据晶振和相应的波特率修改分频器就可以实现！-Written in VHDL serial send, receive, process, according to crystal and the corresponding baud rate divider changes can be achieved!
sim_uart
- uart 收发器 verilog 代码，实现自收发功能 sys clk = 25m, baud 9600 停止位1， 无校验位； 代码实现了串口自收发功能，及把从 PC 收到的内容都发送会 PC, 其他波特率，自行修改代码即可，在 alter 的FPGA 上调试通过； -verilog code uart transceiver to achieve self-transceiver function sys clk = 25m, baud 9600 1 stop bit, no par
sdram
- 通过 UART 读写 SDRAM verilog 源代码 通过 UART 的接口发送命令来读写 SDRAM 命令格式如下： 00 02 0011 1111 2222 00： 写数据 02： 写个数 0011： 写地址 1111 2222： 写数据， 是 16 bit， 每写完一个数据，向串口发送 FF 回应； 输出： FF FF 01 03 0044 01: 读sdram 03： 读的个数 0044: 读的地址 输出： xxxx xx
UART
- UART发送verilog源码，波特率115200，以及testbench源码-Send verilog source UART baud rate 115200, and testbench source
uart
- 串行异步收发接口，简称UART，是一种广泛应用的串行传输接口。这是用vhdl实现的程序，将UART分成相应的几个模块，并用顶层文件进行模块化设计。-Send and receive asynchronous serial interface, referred to as the UART, is a widely used serial transmission interface. This is achieved using vhdl procedure to the appropriat
UART
- 利用Verilog实现UART收发数据功能-Verilog UART send and receive data functions to achieve
Fix-data-send-UART
- Fix data UART send and receive verilog codes.
uart_rx
- Verilog实现的RS232发送和接收程序，有完成的verilog代码，testbench等。(UART send and receive verilog code, including verilog source code, testbench etc.)