搜索资源列表
uart
- 通过avr单片机的uart与pc机通信，通过串口调试助手上发送1—f控制单片机板上的数码管-Avr通过MCU UART communication with the pc through the serial debug aide sent on 1-f control of single-chip digital control panel
yejing
- 通过avr单片机与pc机通信，在串口调试助手上发送字符串，然后返回到串口调试助手上且显示在单片机板的1602液晶上-Avr with pc through the single-chip communication, at serial debugging aides on sending the string, and then back to the serial debug assistant on board and displayed in the single-chip LCD on
SerialCommunication
- 串口通信 包含单片机与PC机通信和单片机与单片机之间的串口通信 内附电路仿真和源程序-Single-chip serial communication includes communication with the PC and the MCU and single-chip serial communication between the enclosed circuit emulation and source
I2C
- MSP430F147,ST7920A,片上AD，通过uart与上位机通信，上位机程序采用VB编写，另外单片机采样数据通过EEPROM保存。-MSP430F147, ST7920A, chip AD, through the uart communicat with PC, PC s programme finished by VB, and sampling data preserved in EEPROM.
usb
- 单片机与USB进行传输，并通过指令来控制PC机的操作-Microcontroller with USB transmission, and through commands to control the operation of PC-
a
- 用单片机采集人体的脉搏信号,并用单片机通过串口与PC机通信.-Collecting the body s pulse signals with the MCU.
danpianjiyupcji
- 单片机与PC机串口通讯仿真。对于学习串口的新手来说，很有 效-Microcontroller with PC Serial communication simulation. For the novice to learn the serial port, it is very effective
CH375DRV.ZIP
- 应用CH375/CH372实现单片机与PC机端通信，所需的windows驱动程序和动态库。-Application CH375/CH372 MCU and PC-side communication, the necessary windows drivers and dynamic libraries.
temperature
- 用2片DB18B20测量温度，0.5秒刷新一次显示在PC机上，格式为“T1=温度1,T2=温度2,A=平均值”。单片机与PC机用MAX232连接。-Temperature measurement using two DB18B20, 0.5 second refresh time displayed on the PC, the format of " T1 = Temperature 1, T2 = temperature 2, A = average." With a MA
Uart_com
- 本程序为STC89C52与PC机超级终端通讯的实验程序 在PC机键盘上输入字符，单片机接收，并发送回PC机，显示在超级 终端；超级终端配置为：波特率为9600，数据位8，奇偶校验：无 停止位：1；硬件：无-This program is STC89C52 communication with the PC HyperTerminal experimental procedures on the PC keyboard to enter characters, single-chip
chapter1
- 单片机的概述，与PC机的异同，学习单片机的第一课 -An overview of the microcontroller and the PC, the similarities and differences
main
- 此为msp430单片机串口程序，实现单片机与pc机的通信。-This is the msp430 microcontroller serial communication program.
51withUart
- pc机与51单片机之间实现串口通行，并将4*4键盘值送pc，pc送来的值在数码管上显示-pc and 51 between the microcontroller and serial passage, and 4* 4 keyboard value to send the pc, the pc values sent in digital tube display
5a60s2
- 通过单片机控制USB与上位机通信，USB用的是南京沁恒公司的CH372-USB Communication between PC and microcontroller control
zhongduan
- 用PIC单片机内部定时器0，作为16位定时器使用，并开启溢出中断。单片机的外部中断0引脚接开关SW2，并设置为下降沿的触发方式。单片机的UART接口工作于全双工异步模式，1个起始位，8个数据位，1个停止位，波特率为9600，并开启接收中断，与PC机通信。编写程序实现功能：SW2按键按下时，LCD上显示“Timer0 Start”, 定时器0开始工作，然后LCD上显示“Timer0 Working”,当UART接收到PC机发送的命令“P”时，定时器0停止工作，LCD上显示“Timer0 Stop”
chuangxing
- 配置CCP1模块使之工作于PWM模式，并初始化周期和占空比。单片机的UART接口工作于全双工异步模式，1个起始位，8个数据位，1个停止位，波特率为9600，并开启接收中断，与PC机通信。编写程序实现功能：当UART接收到命令“S”时，LCD上显示“PWM Start”, PWM开始工作。当UART接收到命令“U”时，占空比增加，当UART接收到命令“D”时，占空比减少，并在LCD上显示占空比。当UART接收到命令“P”时, PWM停止工作，LCD上显示“PWM Stop”。并用示波器观察PWM输
PIC-and-PC-communicate-Via-485
- PIC单片机与上位机以485方式通讯代码，内含CRC校验算法，经测试通过。代码风格利于阅读。-PIC microcontroller with the host computer communication code 485, containing the CRC checksum algorithm, after the test. Coding style is conducive to reading.
code
- 单片机与PC机串口通讯仿真，适合初学者。需要的下载吧-MCU and PC serial communication simulation, suitable for beginners, you need to download it
PS2-STC12C5A60S2-comunication
- STC12C5A60S2单片机 （1）单片机与PS2标准键盘通信，读取键盘按键 （2）读取PS2标准键盘所有按键并显示 （3）单片机与PC机通信，PC机显示单片机发送的数据 （4）利用串口调试助手显示单片机读取键盘按键-STC12C5A60S2 PS2 comunication
s13_lab11_a
- 单片机与PC机通信实验,P1口接8位发光二极管，P2口接8个开关，串行口插座与PC机相连。 2编制程序： 2单片机从P2口读入开关的状态，通过串口发送给PC机； 2PC机发给单片机的数据显示在8位发光二极管上。 -SCM and PC communications experiments, P1 port access eight light-emitting diodes, P2 mouth then eight switches, sockets and serial por