搜索资源列表
80C51
- 关于闭环的控制直流电机的程序，简单的外部中断，实现控制电机转速的问题
pwm-led
- 通过按键加件PWM频率，来控制电机转速或者调灯亮度等，并显示到LED PIC16F74-PIC16F74 PWM-LED
s7200andtouchpanelMT8000controlservomotor
- s7200加触摸屏MT8000实现双伺服电机加减速时间可调控制，伺服电机转速成比例运行。-s7200 plus touch screen MT8000 dual servo motor control acceleration and deceleration time is adjustable, servo motor speed is proportional to the run.
51MCU-control-direct-current-motor
- 用51单片机 通过uln2001a 来驱动直流电机，并且可以通过单片机实验板上的键盘来控制电机转速-MCU with 51 to drive the DC motor through uln2001a and microcontroller experiment boards through the keyboard to control the motor speed
STEP-7---PID-control
- 单片机向LM629给初值，LM629根据所给参数开始调节直流电机转速，编码器反馈值送回LM629，重新修改参数，控制电机转速。-Microcontroller to the initial value to the LM629, LM629 began to adjust parameters according to the DC motor speed encoder feedback value back to the LM629, re-modify the parameters to
Speed-Monitor
- 脉冲宽度测电机转速，用51单片机实现并且在5X7点阵上显示 -Pulse width motor speed MCU with 51 dot matrix display and in 5X7
ch4come
- 甲烷浓度采集，控制电机转速，CAN与上位机通讯。-Methane capture and control the motor speed, CAN and PC communications.
PWM
- LabVIEW输出PWM并由myDAQ输出，用于控制电机转速或舵机转角-LabVIEW output PWM the by myDAQ output for controlling the motor speed or steering gear corner
fske-dianji
- 飞思卡尔用XS128的PWM口写的控制电机转速的程序-Written procedures to control the motor speed by Freescale XS128 the PWM port
zhiliudianjiyuanli
- 通过按键调节直流电机转速，同时在数码管上显示相应的转速。通过控制单片机输出不通过占空比的PWM信号来控制直流电机的转速值。-Button to adjust the DC motor speed, digital tube display of speed. Do not pass through the control of microcontroller output duty cycle PWM signal to control the DC motor speed value.
cx
- 电机转速调节。采用PID调节，可实现电机实时转速跟踪-The motor speed regulation. PID regulator motor can achieve real-time speed tracking
zhiliudianj
- 在控制电机转速方面很多人苦恼，不要紧有了这份资料后你会知道的，附有keil和protues仿真图，方便读者更快的掌握它-Does not matter with this information, you will know a lot of people upset in the control of motor speed, with of keil and protues simulation Figure, the convenience of the reader grasp it f
The-windsurfing-control-system
- 单片机控制电机转速来控制帆板角度，可以通过帆板角度反馈调节电机转速-Microcontroller to control the motor speed to control the windsurfing angle , motor speed feedback regulation by windsurfing angle
pidaicheng
- 设计单片机系统拟实现电子调速皮带秤。本系统利用称重传感器测量输送带有效称量段上物料的重量，并将被测重力转换成相应的模拟电压信号，经放大器放大后，由A/D转换成数字量。与此同时，速度传感器将皮带速度转换为计数脉冲后进行整形。2路信号都送到C8051F410中进行计算、处理，得到当前皮带秤的瞬时流量值，对瞬时流量进行积分得到一段时间内的累积重量。瞬时流量与给定流量进行计较，运用PID算法，输出控制信号控制变频器来改变电机转速，从而可以实现流量的闭环控制。此部分需要设计2路信号输入通道，分别为称重传感
stepper-motor-speed-digital-display
- 利用C51单片机进行的步进电机转速数码管显示-C51 microcontroller stepper motor speed digital display
monitor-pwm
- 通过脉冲调节技术，实现对电机转速大小的精确控制-Adjusted by pulse technology to achieve precise control of the size of the motor speed
motor-control
- 步基于ATMEGA8单片机的步进电机转速和转角的控制，基于中断的方向控制，LED数码管速度显示。-stepping motor control by ATMEGA8 MCU.
step-motor
- 单片机步进电机控制程序 通过脉冲数控制电机转速和转矩 -Single-chip stepper motor control program to control motor speed and torque by the number of pulses
Damo1onlyMotor
- 实现调整PWM数值 控制四个无刷直流电机转速。已调试通过。-Adjust the PWM to achieve numerical control four brushless DC motor speed. Debugging has passed.
交流电机dsp源码
- 使用DSP28335完成交流电机的矢量控制，获得的转速效果和转矩均比较稳定