搜索资源列表
redboot-strong-rel-v0.2.tar
- 程序可作为Bootloader(支持启动脚本功能)、支持GDB源代码级调试、Flash在线烧写。支持网络、串口通信调试，支持TCP/IP协议、HTTP/TFTP、xyzModem协议下载程序。可源代码级调试uClinux内核。 硬件：思创黄金开发板(S3C44B0X/SST39VF160/RTL8019/10M OSC)。 硬件配置： CPU:S3C44B0X RAM:8M FLASH:SST39VF160 OSC:10M NET:RTL8019
Fine-gainedFlashAccess
- * 一、功能: Fine-gained Flash Access驱动演示代码. * 二、运行前提: 本范例需要硬件开发板的支持, * 要求硬件开发板具备名为”ext_flash”的CFI Flash或EPCS Flash模块
USB-Mass-Storage
- 通过STM32的USB实现对SD卡和内部Flash，Nandflash的读写-access to the internal flash,SD card,and Nand flash using stm32
FatFs_R0.07e_Jan15-2010
- FatFs R0.07e by Mr.ChaN from Electronic Lives Mfg. http://elm-chan.org This functions are intended for high level data access to MMC/SD/SD HC Flash memory cards formated using the FAT12, FAT16 or FAT32 standards-FatFs R0.07e by Mr.ChaN from Electron
Windows_XP_Embedded_How_to_install_RAM_EWF_withou
- A guide on how to install RAM (Random Access Memory) - EWF (Enable Write Filter) without temporary partition when using Windows XP Embedded Image. This could be needed specifically when we are using a flash based storage media with the target board,
S3C2440A_Nand_Bootloader
- 由于Nand Flash不能直接线性的访问，所以对于烧到Nand的上的程序，处理器无法直接执行，为了解决这个问题，S3C2440A在内部设置了地位于0x0000_0000容量为4Kbytes的SRAM，在处理器上电时会通过内部电路自动把Nand里头4k的程序（bootloader）装载到SRAM执行，这里称其为小程序，小程序执行后 再装载Nand里位于4K以后的大程序到SDRAM执行。-As Nand Flash can not directly access a linear, so
YAFFS_Direct_User_Guide
- YAFFS_Direct_User_Guide: YAFFS_Direct的用户手册，说明了YAFFS_Direct的结构、移植方法、文件配置等。YAFFS_Direct是可脱离Linux使用的yaffs文件系统，由Yaffs原班人马开发和提供支持。省去了从Yaffs或Yaffs2中提取fs源码的劳苦。 -The user guide of YAFFS Direct. It documented the structure/migration method/configuration of YA
FatFs_R0.08.dev2_April_4-2010
- FatFs R0.08.dev2 April 4, 2010 by Mr.ChaN from Electronic Lives Mfg. http://elm-chan.org This functions are intended for high level data access to MMC/SD/SD HC Flash memory cards formated using the FAT12, FAT16 or FAT32 standards-FatFs R0.08.dev2 A
cf3
- Recovery tool for BCM6348 based DSL routers. This SoC have a bizzare bug, that prevents entering CPU debug mode via jtag, if ADSL controller inside BCM is not initialized (if you compile the original firmware without DSL driver, you are also not be a
USBMem
- The Memory project is a demo program for the Keil MCB2140 Board using the Philips LPC2148 Microcontroller. It demonstrates an USB Memory based on USB Mass Storage Class. LEDs are used to display the following: - P1.16: LED_RD is on whe