搜索资源列表
watchdog
- 键控看门狗演示程序.看门狗演示程序 在16383个机器周期内必须至少喂狗一次。当晶振为11.0592M时在17毫秒内需喂狗一次。 激活看门狗后,喂狗,P0.7、P0.6引脚上的LED闪烁发光激活看门狗后,如果不喂狗,则复位 P0.1、P0.0引脚上的LED闪烁发光
uart.rar
- 基于S3C44B0X的串口通信(led闪烁显示),S3C44B0X-based serial communications (led blinking display)
51单片机控制8个LED闪烁
- 51单片机控制8个LED闪烁,用于学习试验-51 single-chip control 8 LED flashes for learning test
led
- ARM LPC2200 定时器中断使用LED闪烁实验-ARM LPC2200 timer LED flashes interrupt the use of experimental
ARM7
- arm7控制led闪烁的程序。。没有错误-led flashing arm7 control procedures. . No error
Up_Star2410_LED_TEST
- 基于UP_Star2410开发板用汇编语言实现板上LED闪烁代码-UP_Star2410 development board based on the use of assembly language code to achieve on-board LED flashes
UART0InterruptLED
- ADS1.2下的串口控制LED闪烁程序,可以通过PC改变LED闪烁频道-ADS1.2 under the flashing LED serial control procedures, you can change the LED flashing through the PC channel
LED
- LED闪烁通过单片机I、O口控制led灯的闪烁 利用单片机的定时器来实现时间的控制-LED flashes through the microcontroller I, O port control led lights flashing MCU timer using the time control to achieve
AT91SAM7X256-PMC-IAR
- 程序说明: 一、开发环境 1、开发板:AT91SAM7X256 -EK 2、仿真器:SAM-ICE(ATMEL) 3、开发软件:IAR4_30A-1_2(IAR) 二、程序功能 1、程序目的:介绍AT91SAM7X256 PWC的基本用法: 2、 功能说明: 1)、通过PWC设置系统时钟 2)、通过PWC设置各外设时钟 3)、通过PWC的可编程外部时钟信号PCK0输出4.608M时钟 3)、进入空闲模式 三、开发板设置 1、依
timer0_2
- CPLD+MCU电压采集系统 测试程序+原理图\测试程序\定时器\用定时器T0方式1控制LED闪烁-CPLD+ MCU voltage acquisition system Schematic test procedure+ \ Test Programs \ timer \ timer T0 Mode 1 control with LED flash
CC2430-keyled
- Zigbee CC2430按键控制LED闪烁-Key Control LED flashes CC2430
LED-flash-timer--cc2430
- 物联网必学芯片:cc2430 实验例程:利用定时器实现LED闪烁 虽然源程序可以用VC打开,但工程的开发环境应为IAR Embedded Workbench-Things will learn chips: cc2430 experimental routine: use timer, LED flash can be used although the VC open source, but the engineering development environment should
led
- LED闪烁程序利用IO口来控制板上LED灯的亮和灭,使用的是CORTEX-M3核心板和lm3s6965的MCU,在keil中编译下载即可运行。-Flashing LED program uses IO port control board LED lights turn on and off, using the CORTEX-M3 core board and lm3s6965 MCU, the keil compiler download to run.
led
- 嵌入式的led闪烁实验程序及电路仿真和实验结果,包裹程序和电路。-Led twinkle of embedded experiment procedure and circuit simulation and experimental results, parcel procedures and circuit. Led twinkle of embedded experiment procedure and circuit simulation and experimental results
led
- AVR单片机4种LED闪烁方法,包括左移,右移,明暗交替,随机点亮-AVR microcontroller LED flashing method, including the left, right, alternating light and dark, random light
CC2530-LED
- CC2530 LED闪烁交替基础实验 通过该实验可以了解CC2530的工作-CC2530 LED flashes alternately basic experiments can learn through this experiment CC2530 work! !
STM32F10x.ADC.SinWave.LED
- 基于STM32开发,实现正玄波发生,ADC采样,LED闪烁等基本功能,适合新手学习。 直接编译下载可运行-based on stm32
LED闪烁
- 单片机中流水灯实验,LED闪烁,非常完整,好操作。(Experiment of water lamp in single chip microcomputer)
1.协议栈工作流程和无线收发控制LED
- 协调器和终端组网成功后LED闪烁。说明组网成功(LED blinks after coordinator and terminal networking successfully)
5 闪烁一个LED
- 初学者入门,使用单片机简单的使一个led灯闪烁(Simple to make a LED light flashing)