搜索资源列表
-
0下载：
用ADC0809完成模拟信号到数字信号的转换。输入模拟信号由A/D转换单元可调电位器提供的0～5V，输出数字量显示在显示器屏幕上-Complete with the ADC0809 analog to digital signal conversion. Input analog signal by the A/D conversion unit adjustable potentiometer provided 0 ~ 5V, digital output displayed on the m
-
-
0下载：
用ADC0809完成模拟信号到数字信号的转换。输入模拟信号由A/D转换单元可调电位器提供的0～5V，输出数字量显示在显示器屏幕上。显示形式为：AD0809：IN0 XX。 -Complete with the ADC0809 analog to digital signal conversion. Input analog signal by the A/D conversion unit adjustable potentiometer provided 0 ~ 5V, digital out
-
-
0下载：
通过电位器的两端接地和+5v中间抽头接adc，根据adc读取的值在数码管上显示旋转的角度。-Grounded at both ends of the potentiometer and the+5 v intermediate tap connected to adc, adc read according to the value of the digital display on the angle of rotation.
-
-
0下载：
数字电压表：利用模数转换芯片ADC0832实现，输入电压经89k电阻和10k精密电位器分压，测试电压为0～51v，可用表校对-Digital voltmeter: the use of analog to digital conversion chip ADC0832 achieved, the input voltage through 89k and 10k resistors precision potentiometer divider, a test voltage of 0 ~ 51
-
-
0下载：
MCP41010与单片机at89c51联合控制LED灯的亮度，数字电位器与单片机联合应用-MCP41010 and microcontroller at89c51 joint control the brightness of the LED lights, digital potentiometer with a microcontroller application
-
-
0下载：
i2c运用在数字电位计中，控制数字电位计-i2c used in the digital potentiometer to control the digital potentiometer
-
-
0下载：
A simple C file that fades in and out an LED attached to Arduino UNO with the use of a potensiometer.
The code is C. The potentiometer has to be attached to analog pin 0 and the LED to digital pin 6. It uses both ADC
( analog to digital conversi
-
-
5下载：
TI公司的TPL0501数字电位器芯片的驱动源程序代码-TI' s TPL0501 digital potentiometer chip driver source code
-
-
0下载：
PIC编程实例第八章，包含4个程序：
S081: 采用查询方式把模拟通道AN0的10位A/D转换结果送D口，C口显示
S082: 采用中断方式把模拟通道AN0的10位A/D转换结果送D口，C口显示
S083: 测量电位器RV2对地阻值并显示在四位数码管上。
answer: 习题编程题答案-PIC programming examples in Chapter VIII, contains four programs:
S081: using queries AN0 anal
-
-
0下载：
DS1666 数字电位器，通过编程可以改变电阻值，用于程控改变放大倍数，音量等应用中。测试51单片机通过，观察输出wiper和low terminal两端的阻值，呈现增大然后减小的趋势。-DS1666 digital potentiometer, the resistance value can be changed by programming for programmable magnification change, volume and other applications. 51 si
-
-
0下载：
VERILOG编程，利用状态机实现对TLC549的采样控制，实验时可调节电位器RW1（在开发板底板左下角），改变ADC
的模拟量输入值，数据采集读取后在数码管上显示。
-Implementation of sampling control of TLC549 using state machine, adjustable potentiometer RW1 experiment (in the development board bottom left corner), change t
-
-
0下载：
c语言编写的用于51单片机的数字电位计X9313的驱动程序-C language driver for 51 MCU of X9313 digital potentiometer
-
-
0下载：
通过数字电位器实现整个电路的运放功能，进而提高整个电路的计算精度-Via digital potentiometer entire circuit op amp function, thereby increasing the accuracy of the entire circuit
-
-
2下载：
利用单片机通过模拟SPI线控数字电位器，使数字电位器输出想要的电阻值。(Using MCU to simulate SPI wire controlled digital potentiometer)
-
