搜索资源列表
-
0下载:
M16-19264示波器
位 定义 默认
================
0 运行状态 运行
1 触发模式 上升沿
2 画点模式 连线
3 DivY
4 Output_Freq
5 DivX
6 触发电平
7 频率
-M16-19264 oscilloscope define default bit Operation Status 0 1
-
-
0下载:
在电源输入的前端利用旁路去耦电容滤波器,在+12V输入时,首先通过一个电解电容C1和电容C2保证电压的输入稳定,之后选择利用稳压器NCP1117ST50T3G将输出电压降到+5V,如图3.5所示,其输出电流为1A。在稳压器之后继续采用一个电解电容C3来保证输入到芯片的供电电压稳定。-Power input at the front end of the use of bypass decoupling capacitor filter when+12V input through a first
-
-
0下载:
CS4344/5/6/8
10-Pin, 24-Bit, 192 kHz Stereo D/A Converter
-
-
0下载:
STM32模板 V3.5固件库systick精确定时_TIM2轮询_modbus支持 特别适合初学者快速启动开发-STM32 Template V3.5 Firmware Library systick Precise Timing _TIM2 Polling _modbus Support Ideal for beginners Quick Start Development
-
-
0下载:
硬件设置小工具,电阻值计算excel,表列出了常用电阻值,只需要输入电源电压,需要电压俩个电压值,就可以算出分压电阻,误差5 以内会有绿色标注-Hardware settings gadgets, resistance calculation excel, table lists the commonly used resistance, only need to input power supply voltage, the need to voltage two voltage values
-
-
0下载:
With 2.5V - 5.5V power the LV-MaxSonar® -
EZ1™ provides very short to long-range
detection and ranging, in an incredibly
small package. The LV-MaxSonar® -EZ1™
detects objects 0-inches to 254-inches
(6.45-meters) and provi
-
-
0下载:
5串电池电压采样,均衡电流的电路绘制,单片机实现电池包保护电路- Five battery protoction board
-
-
0下载:
#define F_CPU 16000000 // run CPU at 16 MHz
#define LED 5 // Boarduino LED on PB5
#define ClearBit(x,y) x &= ~_BV(y) // equivalent to cbi(x,y)
#define SetBit(x,y) x |= _BV(y) // equivalent to sbi(x,y)
-
-
0下载:
Check the clock frequency & that the baud rate required can be achieved. Error of <1 is never a problem, <2 will work but is undesirable, 5 will not work. Note that this assumes that the other end of the link has perfect timing, which will norm
-
-
0下载:
基于proteus平台,采用8086处理器,利用汇编语言编写,可作为微机原理课程设计。设计一套十字路口的交通灯管理系统,通行时间(或禁止时间)30秒,准备时间3秒,在准备时间里黄灯闪烁3次,闪烁频率为0.5秒,周而复始。若有紧急情况(救护车通过),申请中断,四个方向全部红灯,10秒后重新开始。(进一步设计,可以利用实验箱上的多位数码管显示两个方向的倒计时,或LED点阵显示停、行汉字或动画)(Based on the Proteus platform, using 8086 processors
-
-
4下载:
JEDC DDR-5 Standard. DDR-5 标准。(JEDC DDR-5 Standard. JESD79-5 DDR5 Spec Early Draft Rev0.1)
-
-
0下载:
高频设计辅助工具
电气工程软件,高级电机工程实验室。拥有20多个特性工具专为设计网络、传输线、变压器等设计。它也可以计算线圈和变压器和各种类型的过滤器以及运行噪音等。它可以计算RX和TX系统。AdLabPlus包括一个非常强大的Smith曲线图程序。(AdLabPlus contains AdLab/CSmith and features 5 new electrical engineering tools, for instance for designing active and pass
-
-
0下载:
三星SC2440的核心板,金手指封装,8层板,用PADS9.5打开,也可以用AD10以上的打开(SC2440's core board, gold finger packaging)
-
-
0下载:
JLINKV9.5 原理图,方便自己制作JLINK 下载连接器和相关维修JLINK
-
-
1下载:
全书共19 章,主要内容包括:原理图设计,元件库制作,PCB 元件的布局、布线,Gerber 及相关生产文件输出的设计流程,PADS 高级功能应用,多层印制电路板的设计原则与方法(The book consists of 19 chapters, including schematic design, component library production, layout and wiring of PCB components, design process of Gerber and re
-
-
0下载:
PADS9.5常用元件库,希望能帮助大家。(Common component library of PADS9.5)
-