搜索资源列表
pathloss&gnoise
- cp0801_pathloss为UWB信道损耗计算函数，利用a=(c/(d^gamma))计算出信道增益，然后对函数的输入信号幅度进行变换得到输出结果。 cp0801_Gnoise1和cp0801_Gnoise2为产生AWGN的函数，分别为Eb/No和Ex/No条件下AWGN的产生-cp0801_pathloss for UWB channel depletion calculation function, use a = (c / (d ^ gamma)) calculated Chann
%BE%AB%CD%A8matlab%D7%DB%BA%CF%B8%A8%B5%BC%D3%EB%D
- MATLABThe CD-ROM accompanying this book contains MATLAB® M-files (MATLAB language source code) and Simulink® block diagram models for designing, implementing and testing control systems.
turbobianma
- 一个turbo码的仿真程序，输入Eb/N0值，随着传输帧的增加，误码率增加，得到400帧的误码率。-a turbo code simulation program, the value of imported Eb, with the transmission of the frame, BER increasing, and the 400 bit error rate.
MPSK_sim
- 这是一个非常好的mpsk仿真程序。其中包括BPSk，QPSK，8PSK,16PSK的BER和EB/N0曲线，SER和ES/N0曲线。
finalreport
- matlab实现的多个基础程序和报告并有流程图（1） 绘出正弦信号波形及频谱。 （2） 单极性归零（RZ）波形及其功率谱，占空比为50％。 （3） 升余弦滚降波形的眼图及其功率谱。滚降系数为0.5。发送码元取值为0、2。 （4） 最佳基带系统的Pe~Eb\\No曲线，升余弦滚降系数a=0.5，取样值的偏差是Ts/4。 （5） Pe~Eb\\No，升余弦滚降系数a=0.5，取样时间无偏差，但信道是多径信道，C(f)=abs(1-0.5*exp(-j*2*pi
program
- 典型混沌系统的非线性鲁棒控制同步论文及其MATLAB程序实现 某典型混沌系统同步控制，所采用的方法是非线性控制，将非线性系统在控制器的作用下转化为标准的线性系统。从而消 除非线性混沌现象。附件包含了所参考的论文和MATLAB仿真程序。是利用非线性控制实现混沌系统同步很好的参考文献。 引用请注明原文章出处，如果你参考了本平台的程序也请注明出处，谢谢合作！The author is zeng zheng, college of electrical engi
Task2new
- This prorgam calculates Bit error rate on awgn channel with a particular Eb/No values and plot the graph of BEP(Bit Error Probability) against Eb/No.
EB_POWER_THEFT_IDENTIFICATION_USING_POWER
- EB power theft identification
QAM_Eb_No_SER
- calculate the theoretical exact(in AWGN) SYMBOL ERROR RATE(Ps_SER) verses Eb/No for even numbers of bits per symbol in qam modulation
qpskzjm
- matlab实现矩形脉冲和根升余弦脉冲的QPSK调制功率谱密度及不同信噪比信道下的星座图，直接运行main函数即可-Plot the power density spectrum of the transmitted signal (e.g., with the matlab function psd) with different pulse shapes. How is it affected if a root raised cosine pulse is chosen instead o
10000bitsbipolar
- 产生一个10000位的bipolar信号并画出bit error performance的模拟图像，求出BER-The source generates equally probable bits, P(0) = P(1) = 0.5. (a) Construct a program to generate 10000 bits with bipolar signaling. (b) Use your program to simulate the bit error performan
MATLAB
- this an example of LDPC code in which after encoding i have added AWGN(Additive white Gaussian noise) and bsc(binary symmetric channel). then i hav performed decoding operation. one can easily devloped different BER vs Eb/N0 graph of different channe
7456
- Besides calculating the SER verses Eb/No for the various levels of QAM, The m-file shows the coding gain required to closely approach Shannon s channel capacity limit for 4QAM,16QAM,64QAM,256QAM and 1024QAM. Notes are given at the end of the m-file
channel_awgn
- This code simulates a communication AWGN channel with matlab. You can specify No (noise spectral power) and Eb (bit energy).
bpsk
- BPSK在AWGN信道下,不同的采样率下不同的EB/NO的误码率仿真-failed to translate
mfsk
- MFSK不同进制下，在不同采样率不同EB/NO时的误码率分析-MFSK under different band, different at different sampling rates EB/NO when the error rate analysis
mpsk_table
- This MATLAB Code plot BER Vs Eb/No for M_ary PSK with different values of M. The user can choose the desired BER and the code will tell what is the required Eb/No to achieve this BER for different values of M. In addition, a plot for shannon limit is
mfsk_table
- This MATLAB Code plot the BER Vs Eb/No for M_ary FSK for differnt values of M. The user can choose the desired BER and the code will tell what is the required Eb/No to achieve this BER for differnt values of M. In addition, a plot of the shannon limi
VDSL_dowm
- VDSL的下行链路仿真。1.下行（局端到用户端）速率：20Mbps，上行（用户端到局端）速率：5Mbps；传输距离为500m；在Eb/N0 = 15dB时实现误比特率Pe<=10-4 2.可用信道频谱：0.138MHz-12MHz 3.双绞线模型采用RLCG模型，传输介质为0.4mm PE cable -simulation of VDSL down link
EB-87
- Adina中邓肯E-B模型的二次开发，可用于土石坝计算-Adina Duncan EB model secondary development can be used for embankment dams calculated