搜索资源列表
PLLSim
- 二阶锁相环Matlab仿真代码，如入两路信号和信噪比，输出锁相以后的信号。可以仿真初始频差，和频率斜升的情况-second-order PLL Matlab simulation code, such as two-way signals and signal to noise ratio, the output signal after the lock-in. Simulation can initial frequency difference, and frequency ramp-up
OFDMsourceCode
- 用matlab仿真实现了25 kHz 带宽内同时传送总共48 kbit/s 的两路语音(每路速率9. 6 kbit/s) 和两路数据信息(速率分别为19. 2 kbit/s 和9. 6 kbit/s) , 仿真结果表明达到了较好的误码性能。并比较了4 种数字调制方式下O FDM 系统的误码性能。-using Matlab Simulation bandwidth of 25 kHz simultaneous transmission within a total of 48 kbit / s
cei
- 本代码是关于用matlab算出两路信号的相位差-the code is calculated on the use of Matlab two signals phase difference
lms-50Hz
- 采集到的50Hz电源信号送至信号处理器作为参考信号，该参考信号在信号处理器中需经HILBERT变换变成两路正交正余弦信号X1、X2，然后采用自适应滤波器算法滤掉有用信号中的50Hz信号。
Music_DOA_3
- 阵列信号处理，一路期望，两路干扰信号的MUSIC和capon的matlab程序。
FastICA_25
- 实现两路信号的分离，效果还不错。在matlab上验证通过。
weibull
- 这是雷达幅度符合韦布尔分布的杂波仿真程序，功率谱为高斯谱，时域上分为I、Q两路。
IR
- 把I、Q 两路信号分别作FFT ,找出频域内信号的幅度,即可算得两路分量的幅度一 ％致性 把I、Q两路信号合成一个复数信号,作FFT ,对得到的频谱求镜像抑制比。
QPSK-I-Q
- matlab仿真程序，产生QPSK调制的信号，严格按照QPSK的调制步骤分I路Q路产生信号，最后两路相加，产生已调信号，调制信号随机产生，载波信号是余弦信号。-matlab simulation program to produce the QPSK modulation signal, in strict accordance with the QPSK modulation of the sub-step road Q road I have a signal, the sum of the
ddc_30m
- 中频70M，30M带宽LFM信号，采样率为102.4M，数字下变频后，还进行了三倍抽取，最后还得到I，Q两路信号 -IF 70M, 30M bandwidth LFM signal, the sampling rate of 102.4M, digital down conversion, the samples were carried out three times, the last also I, Q two-way signal
LTE_Link_Level_1.3_r620
- 维也纳大学的LTE链路级仿真平台,实现了LTE两路及仿真的整个个过程-LTE link lever simulation
Bell_Sejnowski_ICA
- 两路语音信号的Bell-Sejnowski ICA算法 -Basic Bell-Sejnowski ICA algorithm demonstrated on 2 speech signals.
wf
- 实现多通道后滤波技术，即经典的ZK算法，支持两路以上麦克风阵列的通道。-After the implementation of multi-channel filtering technique. Absolute classic.
101259374qpsk_mod_matlab_wy
- qpsk调制的MATLAB实现，串并变换，载波相乘，两路信号相加，实现qpsk调制-MATLAB modulation qpsk realized, string and transform, carrier multiplication, the sum of the two signals to achieve modulation qpsk
bispectrum_tde
- 利用matlab对两路信号进行双谱估计并且计算信号时延-matlab pairs of spectral estimation and delay calculation
ss_Pe97
- 此代码描述的是跳频系统在不采用两路分集的情况下的性能仿真，主要也是对误码率的仿真函数-This code describes the frequency-hopping system without two-way diversity in cases where performance simulation, is largely a function of the BER simulation
GMMforLabData_DPSK
- 用于均衡DPSK信号的JD-MLSE算法，为matlabb程序，输入DPSK解调的两路信号，判决得到所需的bit序列，并计算误码率-It s used for electronical equalization based on joint-decision maximum likelyhood estimation (i.e. JD-MLSE).
s-function
- 编写S函数模块，实现两路正弦信号的叠加，正弦信号相位差为60度-Writing S function module, the superposition of two sinusoidal signals, sine signal phase difference of 60 degrees
efficient_fft_aa
- 两路实数FFT的matlab仿真。硬件实现：一个FFT核实现两路实数FFT。-FFT of two real numbers matlab simulation. Hardware: FFT core to achieve a two-way real FFT.
kcsj
- 基于simulink仿真，应用tdm、pcm、2dpsk技术实现两路语音同时传输-Simulink simulation-based, application tdm, pcm, 2dpsk technology to achieve two-way simultaneous transmission of voice