搜索资源列表
Valve-stiction-model
- 过程工业中带有粘滞的阀门数据驱动模型,模型采用SCI论文《Two-layer banary tree data-driven model for valve stiction》中提出的算法,本人自己独立编制转化,成功运行,性能良好。模型由Matlab文件和Simulink模型两部分完成,且内设注释,可直接运行。-A data-driven model of valve stiction. The algorithm is from the paper"Two-layer banary tree
shiww
- 该文件是在瑞利信道统计的基础上,给出了Clarke模型,并给出了仿真方法-Rayleigh channel statistics based on the file given Clarke model and simulation method
POGO-FVM_Up
- 纵向耦合振动(POGO)是一种常见的工程问题,其数学模型有经典水锤模型、四方程模型和八方程模型等。与此同时,有限体积法(FVM)物理意义明确,守恒性好,控制方程组的离散和数值求解简单,可以很好地应用于POGO问题分析中。附件包含了上述三种模型和不同初值、耦合条件下的m文件,以供参考!-POGO is a common engineering problems, the mathematical models consist of the classic water hammer model, f
acdc
- AC-DC matlab仿真模型 mdl文件-AC-DC matlab simulation model mdl file
control-of-inverter
- 逆变器的预测电流控制,包括M文件和SIMULINK 模型,已经仿真验证-predictive current control of inverter,including M file and SIMULINK model
sga
- 这是一个针对simulink模型的四个参数的基本遗传算法参数辨识的.m文件-This is a basic genetic algorithm parameters for the the simulink model four parameters identification. M files
smallworld
- matlab环境下的复杂网络小世界模型,M文件,可画图-small world in Matlab
nonlinear-system-model
- 以m 文件编写S-Function函数,实现以下Bell 和 Astrom(1987) 关于某160MW燃油机组特性的非线性系统的模型-M file write S-Function function implement following Bell and Astrom (1987) model of the nonlinear system on the characteristics of a 160MW fuel unit
ABC
- 数学建模 病毒传播SIS模型研究中第二小题的m文件,参考自无标度网络的代码,原先做题时运行生成A、B各5000个节点,100次重复运算取平均,整整跑了24083秒,将近7小时- -,后来有空对代码简化,同样的计算,只需要365秒,才6分钟…有兴趣的可以研究下。-The second theme m file in mathematical modeling virus propagation SIS model, reference scale network code, originally
WriteFieldflp
- 在Kraken简正模模型中,用于更改*.FLD场文件的matlab程序-Kraken normal mode model for change* FLD field file matlab program
OPEN1
- 该文件是间接式双级矩阵变换器的开环仿真模型。输出结果符合理论推导。采用s函数编程的方法实现空间矢量调制策略-This file is indirect two-stage matrix converter of the open loop simulation model. Output the results accord with theoretical derivation. The s function programming method of space vector modulat
simengine
- simulink与实体建模软件联合仿真,建立了曲柄连杆活塞机构动力学模型,形成可视化仿真,运行mdl文件即可。对发动机分析设计人员有启示。-simulink co-simulation and solid modeling software, the establishment of a dynamic model of the crank rod piston mechanism, a visual simulation run mdl files can. Engine analysis a
control-of-the-DC-Motor
- 我在德国留学电机控制实验课的直流部分,包括分别对电流环和转速换的校正,并对是否对反馈值加滤波器性能进行对比,并附上了效果图,是学习电机控制基础,程序的效果明显,实现无差控制,并对动态性能和扰动性能进行了测试。先运行初始化文件,然后加载模型,关于初始化文件的注释,都是电机的参数的设置,直接看模型就可以-I study in Germany motor control DC part of the experimental class, including the correction for th
RRR-RRP-simulation
- 机构RRR-RRP仿真,里面有仿真模型,M文件-Institutions RRR-RRP simulation, inside the simulation model file
RRR-PRPsimulation
- 机械机构RRR-PRP运动学仿真,包括速度,加速度的仿真,内有运动模型,M文件。-Mechanical kinematics simulation, including speed, acceleration RRR-PRP.
RRR=PRP
- 机械结构RRR-PRP运动学仿真,包括速度,加速度的仿真结果,里面有运动仿真模型和M文件。-Mechanical structure RRR-PRP kinematics simulation, including speed, acceleration simulation results, there is a motion simulation model and the M-file.
exp2
- 录制汉语拼音 a1(阴平)的发音。分别提交你所能录制的基音频率最高和最低的两个 录音文件。文件名为: 学号_a_h.wav(高音文件)和学号_a_l.wav(低音文件)。(用MathLab 编程) 1)分别对这两个文件进行观察分析。找出最高和最低基音频率位置,分别显示此时它们的 局部波形和短时频谱(按照最大值为100 归一化显示)。 要求:在时域波形上标出基音周期,并算出数值(精确到一个采样点)。在频域图上标出 基音频率。注意:标出分析波形的起始位置(精确到采样点位置),
MFC
- 无模型控制的matlab代码,采用m文件形式,直接可运行,参数预估采用带遗传因子的最小二乘法实现-Model free control matlab code m file can be run directly, the parameters estimated using the least squares method with genetic factors
MATLAB-Optimization-Toolbox
- 文件是一个Matlab优化工具箱,主要内容是线性规划模型、非线性规划模型、二次规划模型、多目标规划模型和最大最小化模型。-The file is a Matlab optimization toolbox, the main content is a linear programming model, nonlinear programming model, quadratic programming model, a multi-objective programming model and
fanke
- 本仿真文件是故障电弧的数学模型的仿真文件,能有效的放着出故障电弧的基本特征,为故障电弧检测的研究提供了方向-This document is arc fault simulation mathematical model simulation files, which can effectively lay out the basic characteristics of fault arc, arc fault detection for the study provides directio