搜索资源列表
synchronous_DAQmx_measurement
- 此程序描述DAQmx同步测量设计：实现DAQmx设备的同步测量-This program is designed to describe the simultaneous measurement DAQmx: DAQmx measurement equipment to achieve synchronization
INT0
- INT0的中断服务程序及脉宽测量 通过按键产生/INT0 有效信号，在P3.4 引脚上输出指示信号；并测量按键操作在/INT0引脚上产生的高电平的脉宽。注意：实际操作时，测试的脉冲宽度有可能超过16 位计数器的定时范围。操作时，考虑用蜂鸣器或指示灯作为状态提示。 -INT0 interrupt service routine and pulse width measurement Produced by key/INT0 valid signal, the output signal
50thermocouple-measurment
- 此程序包含多个热电偶并行测量方法。也可以根据此来修改成相应的压力测量-This program contains multiple thermocouples parallel measurement methods. This also can be modified to the corresponding pressure measurement
yali
- 这是测量压力的labview程序，主要用于测量压力，位移等。-This is used to measure pressure,displacement and so on
HCT99-Measurement
- 实现通过HCT99单次/连续测量的数据采集。-Through HCT99 single/continuous measurement data acquisition.
Basic-Spectral-Measurement
- 用于测量信号频率，这里的输入信号是正弦信号。-Basic Spectral Measurement
DS18B20-temperature-measurement
- 利用128开发板，并通过AVR软件实现 DS18B20温度测量功能。-With a 128 board, and to achieve DS18B20 temperature measurement function by AVR software.
Hilbert-Huang-Transform
- 希尔伯特黄变换，主要用于测量汽车发动机故障，提取故障特征。-Hilbert Huang Transform, mainly used to measure automobile engine fault, fault feature extraction.
UltraV2.0-SOFT-12-09
- 天然气表的驱动程序，包含时间测量芯片的驱动程序-drive program of gas meter
LabVIEW
- 本教程内容涵盖LabVIEW 的编程理论、技巧、特性、VI 和函数，用于创建测 试测量、数据采集、仪器控制、数据记录、测量分析和报表生成等各类应用程 序。-This tutorial covers the LabVIEW programming theory, techniques, characteristics and function, VI, is used to create test Test and measurement, data acquisition, inst
sound-recognition
- 用LabVIEW实现噪声源的识别，能够将噪声源的位置进行测量-With LabVIEW to identify noise sources, the ability to measure the position of the noise source
virtual-camera-
- 通过C++和摄影测量中的共线条件方程实现了由倾斜相片到水平相片的变换，-inclined image to virtual image
Hantek6022BE
- Hantek6022BE虚拟示波器频率、周期、占空比测量-Hantek6022BE virtual oscilloscope frequency, cycle, pulse rate measurement
10562186fz
- ad转换程序adc0809，类似adc0832,在51单片机的稳定测量中有很好的应用。-adc 0809 typical procedure, read the analog voltage into a digital signal
bonedensitymeasuring_LABVIEW
- 超声骨密度测量仪，基于虚拟仪器技术，采用NI采集卡完成数据采集，利用LabVIEW数据处理。-Ultrasonic bone density measuring instrument based on virtual instrument technology, using NI acquisition card to complete the data collection, the use of LabVIEW data processing.
TemperatureDisplay
- 51单片机温度测量及在数码管上显示的汇编语言代码-51 MCU temperature measure and display the temperature in the digital tube
maichongceliang
- 主要运用labview的编程功能完成对信号的脉冲测量分析，从而更好的理解脉冲含义。-The main use labview programming features complete pulse measurements on the signal analysis, so as to better understand the pulse meaning.
tempreture-and-wet-detection
- 通过一些传感器和简单硬件来实现温湿度的测量和显示-use some sensing element to tempreture and wet detection by python
wenjian
- 由随机函数产生0~5V电压值，电压采样时间从0开始，每隔500ms采集一个点，共采集40个点（保留2位小数）。求显示电压随时间变化的曲线，并且把测量的电压存为表格文件。-0 ~ 5V voltage value generated by the random function, voltage sampling time 0 every 500ms capture a point, were collected 40 points (2 decimal places). Demand show
b_point
- GPS测量数据处理可分为基线解算和网平差两个阶段，基线解算就是利用ＧＰＳ接收机接收到的 载波相位观测值做为基本观测值，对其进行差分处理。-GPS data processing can be classified as the baseline solution and flat screen two phase difference, baseline solution is the use of GPS receivers to carrier phase observation value