搜索资源列表
Read-IR-Example
- 读数KNR上的红外的读数,判断是否有障碍物、需要有KNR-Infrared readings on the KNR, to determine whether there are obstacles, the need for KNR
M3uCOSII
- 基于STM32的M3-uCOS-II 多参数传感器开发文件,完整的工程文档,可检测CH4、CO、温度等参数,包含真人语音、AD5207、485、红外、eeprom等等,原创误转载-Based on the STM32 M3-uCOS-II multi-parameter sensor development documents, complete project documentation, can detect CH4, CO, temperature and other parameters
banjian
- 基于Led 128*64 显示屏的红外板间接收发送。-Infrared transmission and reception between the plates.
hw
- 红外遥控器键值数码管显示,,,51单片机实现-Infrared remote control key digital display, 51 MCU
huibian
- 一些比较实用的汇编小程序,包括有倒计时,红外检测,点阵液晶显示等一些小程序。-Some of the more useful compilation of small programs, including the countdown, infrared detection, dot-matrix LCD and some other small programs.
infrared
- 红外通信,使用遥控器给MCU发数据,MCU通过红外线接收数据。-infrared communication
87155028emc_ok
- 这是一个 emc单片机的 红外接收程序 很好用已经试过了 大家可以下来参考参考-the program is emc mcu read_ir it very good usd do you like hehe
hongwailcd
- * 描述: * * lcd1602显示 遥控键值读取器 * * lcd1602显示 遥控器接p3.2 * * 喇叭接p1.5 继电器接p1.4 * * 17(40h)键按下,继电器吸合。19(04h)键按下,继电器关闭。 * * 连接方法:使用红外功能时 J1跳线短接-* Descr iption:** lcd1602 display remote control key reader** lcd1602 displays the remote access p3.2** S
1
- 红外发送数字0到F,包括按键检测,数据传送前的误码检测等-Infrared transmitter number from 0 to F, including key detection, error detection, etc. before data transfer
20140418
- 关于三通道红外安全光线(应用于自动门)的源程序,软件部分。-three channel
HWJS
- 51单片机红外接收解码程序,采用汇编语言编写。-51 single IR receiver decoder procedures, using assembly language.
HWTS
- 51单片机模拟红外发射程序,采用汇编语言编写。-51 single-chip analog infrared emission program in assembly language.
hwx
- 单片机红外发射(原理与设计程序) -SCM infrared emission (theory and design program) microcontroller infrared emission (principle and design process)
dpj
- 单片机红外发射(原理与设计程序) -SCM infrared emission (theory and design program) microcontroller infrared emission (principle and design process)
q-2501
- 用松翰SN8P2501B C语言编写的红外解码,普通IO口接收红外遥控信号-Sonix SN8P2501B C language IR decoding, common IO port infrared remote control signal receiver
remoteCar
- 循迹遥控车,循迹模式下,小车跟着黑带走;遥控模式下,用红外遥控控制小车。两种模式可以自由切换-remote control car
Infrared-transmission
- 红外传输:U13 CD4060B 通过外接晶振电路在第9 端产生一路频率为38KHZ 的方波信号作为调制信号,输入与门U14A 74HC08 的2 端;另一路为需发射的数据,它通过DO14 端输入与门U14A 74HC08 的1 端。输入的数据在与门调制,在其输出端形成调制后的数据波,从而通过Q2 S8050 控制红外发光二极管D13以38KHZ 的频率发出红外光。Q3 1736 为去调制波的红外接收器,它去掉38KHZ 的调制波,解调成原始的输入数据信号,通过3 端输出至U14B 74HC08
hwmcu
- 单片机I/O口采集红外感应人体信号,计数同时送12864液晶屏显示与控制!-MCU I/O port body infrared sensor signal acquisition, while sending 12,864 counts LCD display and control!
ho-wai
- 本文介绍红外简单解码的程序便于学习者很好的理解红外解码的原理-this is a good book
Decode
- 基于义隆单片机的红外nec编码的解码程序,可以解地址码和控制码。-Elan MCU based infrared nec code decoding procedures, can the address code and control code.