搜索资源列表
LED_BCD8x7seg
- bcd 8*7 seg led display code in assembly level coding
display
- labview的文字滚屏显示，效果类似LED屏幕的滚屏显示。-Scrolling Display
interface--experiment1
- 利用汇编语言，进行的接口实验源代码，包括IO地址译码、简单并行接口、可编程并行接口8255方式、七段数码管显示、8255键盘显示控制-The use of assembly language source code interface experiment carried out, including the IO address decoding, simple parallel interface, programmable parallel interface mode 8255, sev
main
- PWM控制输出并通过LED显示PWM值并据有电压电流保护报警输出功能-PWM control output and PWM LED display value and according to a voltage-current protection alarm output function
TH11_8LED
- keil 51 8位动态数码管显示程序,主要实现八位数码管显示“168168”的功能-keil 51 8 led display program
DS18B20
- 以AT89S52单片机为核心设计智能火灾报警系统，包括硬件和软件设计两部分。通过温度传感器DS18B20检测现场参数，经过信号调理电路、A/D转换后送入单片机进行数据处理，通过LED显示实现实时显示，并进行声光报警。-AT89S52 microcontroller as the core design of intelligent fire alarm system, including hardware and software design in two parts. Detected by
dianzishizhong
- 该系统是一个简单的利用8253定时器、8255可并行通信接口和中断控制器8259设计的电子时钟系统，在该系统中设有一个启动键，启动键未按下时，显示初始化界面“HELLO”；当按下启动键时，8253定时器开始计时（8253的初值为10000，接1MHz的脉冲，即当8253计满100时正好是1S），当计时计满100时，8259便产生一次中断，在LED显示器便显示系统预先设计好的初始值“23.59.55”便开始从秒位开始加1，当加到10S时，10s位加1，加到60S时分位加1，同时秒位清零，同时怎加到
led
- 点阵移动显示,类似于现代开发的工业制作产品-Lattice mobile display, similar to the product of the development of modern industrial production
Archive
- to design a 7 segment LED DISPLAY
LED
- 单片机89C52控制LED数码管进行点阵显示-89C52 microcontroller control LED dot matrix display digital tube
LED
- 8×8点阵显示汉字，汉字字符可以是按键来控制命令的输出，如“1”，输出将是“欢迎进入系统”！功能等。-8* 8 dot matrix display Chinese characters, Chinese characters can be keys to control the output of the order, such as by 1 , the output will be Welcome into the system! Function and so on.
LED
- 2-1-3上电数码管显示5，每按一次s2,数码管显示加一，每按一次s3,数码管显示减一，最大显示为A，最小显示为4-The 2-1-3 electric digital tube display 5, each time you press the s2, digital tube display plus one, each time you press the s3, digital tube display minus one, the largest display for A, the
ZX
- 8255C口接逻辑电平开关K0~K7，A口接LED显示电路L0~L7，编程从8225C口输入数据，再从A口输出-8255 C port logic level switch K0 ~ K7, A port LED display circuit L0 ~ L7, programming input the 8225C port, and then the A port output
ffff
- 。用8031单片机经8255A扩展2位8段码LED显示器，用8255A的A口作为段码（字形代码）数据口，PB0和PB1作为位控制端口。在位控制口加集电极开路的反相高压驱动器74LS06以提供驱动LED显示器所需的足够大的电流，然后接至各数码显示器的共阴极端。同理，在段码数据口集电极开路的正相高压驱动器74LS07提供足够大的电流，然后接到数码显示器的各段-Simple calculator needs 8 bit 2 segment code LED display circuit. With
HD2016_V6.1.3
- LED显示屏软件，灰度LED-LED display software, gray LED
[SMG_Dynamic-display]
- 基于STM32F103的6位数码管动态显示驱动程序-STM32F103 based on the 6 digital LED dynamic display driver
calculator
- 用键盘输入计算的数字和运算方式，实现整数且正数类型的运算，并利用数码管显示出运算结果。在每次运算之后，按下清零键进行清除。-Calculated using the keyboard input numbers and operators, to achieve a positive integer number and types of operations, an LED display using the calculation result. After each operation,
（在两个中）识别最大模拟输入通道
- （在两个中）识别最大模拟输入通道 利用0809采集两路模拟电压，将电压值最大的通道号显示在LED显示器上。（硬件电路参见AD_CH2_1.DSN）。((in two) identifying the maximum analog input channel Using 0809 to collect two analog voltage, the voltage value of the largest channel number is displayed on the LED displ
编码显示器
- 利用8255扩展并行端口（硬件电路参见CodeDisplay_8255.DSN）。当KEY按下时，利用8255的PC口输入二进制值编码（6位），将该值转换成十进制后显示在2位7段LED显示器上。(Using 8255 to extend parallel ports (see CodeDisplay_8255.DSN for hardware circuits). When the KEY is pressed, the binary value encoding (6 bits) is ent
test
- 排线测试LED显示，相邻排线间短路则停止跑灯暂停显示等(Cable test, LED display, the adjacent line between short-circuit, stop running, lights, pause, display, etc.)