搜索资源列表
0-99
- 数码管LED显示动态(0-99计数),可以自动计数-LED digital tube display dynamic (0-99 counts)
program
- 交通灯设计,51单片机汇编编程,有LED灯红绿黄闪烁并有数码管显示倒计时,系统带有可调功能,当东西道上出现紧急情况,可立即调节开关,使东西道调到红灯,停止东西道通行。-Traffic light design, 51 assembly programming, there are red, green and yellow flashing LED lights and a digital display counts down system with adjustable features,
dotmatrix2
- 进行动态显示字幕(LED),效果非常不错,希望有需要的朋友下载!-Dynamic display subtitles (LED), good results!
STM8andCY8CMBR3108
- 用3108触摸IC实现按键的触摸控制 (当按相应按键时,所对应的LED亮同时LCD显示从 3108读取到的值) 每当一个按键按下Beep响一下。 MCU用的是STM8s105 -3108 touch the touch control IC achieve key (when press the corresponding button, the corresponding LED and LCD display the bright 3108 read
VC43_20130915
- PGA4311音响音量调节芯片驱动,LED段码显示功能。可以作为前级等试用。-PGA4311 driver. LED segment display.
Text1
- 利用单片机AT89C51控制DS18B20温度传感器对水温控制,当水温低于预设温度值时系统开始加热, 红色发光二极管点亮表示进入热状态,当温度达到预设温度值时自动停止加热,红色发光二极管自动熄灭。预设温度值和实测温度值分别由两个3位数码管显示,范围为0~99℃-Control using SCM AT89C51 DS18B20 temperature sensor temperature control, when the water temperature is lower than the
8259
- 8255方式0,由A口(B口、C口)输出数据,驱动四个LED,使其顺序显示 ‘0’~‘F’的二进制状态,每个状态保留1秒钟。-8255 mode 0, the A port (B port, C port) output data to drive four LED, so that the order of display ' 0' ~ ' F' binary state, each state retained a second.
8051c
- 8051 基本程式 有關LED 七段顯示器 LCD 蜂鳴器-8051 relating to the basic program buzzer LED LCD segment display
shizhong
- 利用定时芯片8254,可编程并行芯片8255,LED芯片,进行时间的显示-8254 with a timing chip, programmable parallel chip 8255, LED chip, the time display
16_16dianzhenziku
- LED电子显示屏 自动生成汇编格式和C语言格式-LED electronic display screen
8255A
- 1、 设计一个电路,由8086通过8255A读取四个开关的状态,然后通过查表输出结果由LED七段数码管显示相应的数字。例如:当四个开关全部断开,读取的数据为1111,则数码管显示F。画出电路图、按要求编写程序,在仿真环境下调试通过。-a circuit design 8086 through 8255A Reads four switch status, and then display the corresponding number the LED seven-segment LED o
Simulate-the-elevator-system
- 这是一个labview的应用实例,主要功能是模拟电梯工作系统,里面还应用了LED矩阵滚动屏,和数码管显示楼层。用Labview做主机(电梯梯轿主控制面板),protues仿真51单片机做从机(各楼层控制面板),串口通信,实现电梯工作系统的模拟-This is a labview application examples, the main function is to simulate the elevator system, the LED inside the application mat
hanzixianshi
- 在8X8的LED点阵显示器上显示汉字“大”-Display Chinese characters on LED 8X8 dot matrix display
Simple-Math
- 将两个输入的数字相加并显示结果;将同样两个输入数字相乘并显示结果;比较两个输入数字,如果数字相等,则LED指示灯亮。最后,保存为Simple Math.vi文件。-Adding two digital inputs and displays the results the same figures multiplying two input and display results compare two input numbers, if the number is equal, then
password
- 单片机密码锁源程序和原理图:用4*3的键盘组成0~9的数字键及确认键、删除键;用8位数码管组成显示电路提示信息,当输入密码时,只显示“—”,当密码位数输入完毕按下确认键时,对输入的密码和设定的初始密码进行比较,若密码正确,则开锁,此时P3.0口的LED(即黄灯)亮一秒作为提示;若密码不正确,禁止输入3秒种,同时发出报警声。初始密码为8位。 增加功能:利用外部中断0和1分别实现复位和密码修改功能 -SCM locks source code and schematics: 4* 3 ke
Keypad_LEDPLCD
- this program is use to read input keypad 4x4 and display the output at LED.. -this program is use to read input keypad 4x4 and display the output at LED..
LCDDEMO
- 8051单片机 LCD Display Driver Demo. LED程序显示 Timing code assumes 1.2MHz Clock-8051单片机 LCD Display Driver Demo. LED程序显示 Timing code assumes 1.2MHz Clock
GLFDQ
- 为51单片机控制的音响功放板 一.带有3路外接音频信号输入: 1. 音频信号输入,可通过音频线输入CD、电脑、手机等音频信号。 2. 自带数字收音模块输入。 3. 通过3P针座预留外接输入。 4. 通过一个2P针座向外提供5V电压,一个2P针座提供单片机串口。 二.实现音频信号左右两路声道信号输出,可通过外接12V电压,1A以上适配器供电。或者通过8-10V交流电压供电。 三.由4位数码管显示,10个LED灯在无音频信号时为跑马灯模式;有音频信号时LED灯跟随信号强弱
10-hex-binary-transfer
- 将一个10进制的数转化成二进制的LED灯显示-A decimal number converted to binary LED light display
number_display
- FPGA控制4个7段数码管动态显示,可以为FPGA其他实验做校验中间结果使用- FPGA control 4 LED Segment Displays to dynamic display, can be used for FPGA other experiments to do check the results of the middle