搜索资源列表
control
- 该代码是完整的BLDC正旋波驱动解决办法,电机可以正常运行-The code is complete BLDC spinning wave-driven solution to allow normal operation of motor
cn023744
- Sensorless BLDC Motor Control Using dsPIC30F2010 1127KB
Sensorless-BLDC-Motor-Control
- BLDC驱动程序，PIC18F2431，1000行左右，驱动能力300w，包括电路图-Using the PIC18F2431 for Sensorless BLDC Motor Control
bldc
- 无刷直流电机开环程序 电机功率500w 4对极-Open-loop brushless DC motor Motor Power 500w 4 program a very
Source_Code
- Code for running sensored control BLDC motor
87_Kutt_Michna_pop
- this file is about Bldc motor
3741ea570def1d1_ek
- this file is about Bldc motor
114202-6464-IJECS-IJENS
- this file is about Bldc motor
ejsr_35_2_05
- this file is about Bldc motor
v3-284-289
- this file is about Bldc motor
Motor-Drive-BoardBLDC_LV
- BEIJING PRECISION MOTORS & CONTROL SYSTEM CO _, LTD_files 低压BLDC驱动套件\Freescale-BEIJING PRECISION MOTORS & CONTROL SYSTEM CO _, LTD_files\Freescale
bldccontrol
- This used for controlling bldc motor-This is used for controlling bldc motor
BLDC-control
- 有霍尔传感器的直流无刷电机启动换相及比例积分调速控制程序及保护程序，无霍尔传感器直流无刷电机启动及比例积分调速控制程序。-A Hall sensor commutation of brushless DC motor starters and proportional-integral speed control procedures and savers, brushless DC motors without Hall sensors start and proportional-integ
LabVIEW-Simulation-Tutorial---Brushed-DC-Motor.ra
- Labview BLDC modelling
6.5.2-MOTOR-BASIC-RUN
- stm8s直流电机控制适用于航模无刷电机控制-bldc dc moto run detab will at moto foc
sensorless
- This paper develops the brushless dc (BLDC) motor sensorless control system for an automotive fuel pump. The sensorless techniques that are based on a hysteresis comparator and a potential start-up method with a high starting torque are suggest
BLDC_mine
- Bldc motor demonstratiuon program where matlab is used to perform the simulation, the student will find it useful
motor-control-system-in-Labview
- Labview 源码，实现永磁电机控制上位机控制，与dsp2812配合使用，主要用于发出控制信号和接收状态信号。-it is programmed in labview and it is for controlling a BLDC combined with dsp2812. it is mainly used for send control signal s and recieve state signals.
6 BLDC 开环调速
- 此程序是用于BLDC电机驱动的，单片机是STM8S系列的单片机(this codes is used for the BLDC MOTOR DRIVER the MCU is STM8S series)
STC15W401AS实现无刷无感电调控制程序和电路
- 本程序试验使用STC15W401AS-35I-SOP16<RMB1.6>来驱动航模用的无传感器无刷三相直流马达. 本程序参考自网上的代码(作者: 瑞生), 改良而来. 电路图见文件 "BLDC-V10-实验电路.pdf". 控制信号由P3.2输入正脉冲信号, 间隔5~20ms, 脉冲宽度1.000~1.610ms. 1.160ms开始启动, 1.610ms为最高速度, 分辨率为2us. 本程序仅仅是简单控制, 软件没有处理 过0延时3