搜索资源列表
20090226
- 从盲声源信号的独立性出发!提出了一种新的盲声源混合信号分离方法:该方法基于信号联合概率的 分布统计!利用信号联合概率的方向导数熵最小获得最佳的旋转角度!最终实现盲信号分离:与快速独立分 量分析方法及神经网络方法相比!该方法不需要迭代计算:采用新的盲声源信号分离方法对轴承试验台的混 合声音信号进行识别!将电机和滚动轴承的声音分离出来!进而可以准确识别机械的故障-Blind sound source from the independence of the starting signal
dianpianji-labview
- 搜索pudn网上的protues电机，都只是单纯的电路仿真，此文件除此外，还连至上位机运用labview对电机进行控制，是电机整体仿真很有用的源代码。-The the search pudn online protues motor, just the circuit simulation, In addition, even the first bit machine use labview to control the motor, the motor overall simulation
LabVIEW-DLL-program
- 为自制多功能数据采集卡编写了DLL 形式的驱动程序,并将其挂接到labview 开发平台上,利用DLL 驱动程序实现了对步进电机的自动控制.-The driver DLL form prepared by the self-made multi-function data acquisition card, and hooked up to the the labview development platform on DLL driver to achieve automatic contro
LABVIEW-cai-ji
- LABVIEW 数据采集，和电机控制，通过板卡可以控制电机的转速，并且能采集电机的转速信号。程序比较简单，不是采用DAQ编写。-LABVIEW data acquisition, and motor control board can be controlled via the motor speed, and can collect the motor speed signal. Procedure is relatively simple, instead of using DAQ writ
control-the-labview-handwheels-
- 使用labview控制手轮并且读取手轮的数据用于控制电机位置-Using labview control handwheel and read the handwheel data is used to control the motor position
labview
- labview控制K型立方体DC伺服电机控制器运动的程序-Labview control of K-cube DC servo motor controller movement program
motor-control-system-in-Labview
- Labview 源码，实现永磁电机控制上位机控制，与dsp2812配合使用，主要用于发出控制信号和接收状态信号。-it is programmed in labview and it is for controlling a BLDC combined with dsp2812. it is mainly used for send control signal s and recieve state signals.
智能分布式双轴太阳能跟踪采集存储系统
- labview与51单片机串口通信，labview作为上位机，实现电机开关正反转功能(LabVIEW and 51 SCM serial communication, LabVIEW as the host computer, the realization of motor switch positive and reverse function)
电机转速计算
- 采用labview编写的电机转速计算器，输入轮胎直径 、减速比、要求车速，输出所需电机转速(Written by LabVIEW motor speed calculator, enter the tire diameter, speed reduction ratio, speed requirements, the output motor speed required)
直流电机位置控制
- 直流电机位置控制，前面板设置电机指针位置，运行程序，电机即可按照预设值转动。(DC motor position control, the front panel set the motor pointer position, run the program, the motor can be rotated according to the preset value.)
dianji88997
- 基于NI6221卡的电机测试控制程序，由NI6221卡发脉冲控制电机转速，再由6221卡读回电机的转速信号并显示(Motor test control program based on NI6221 card, NI6221 card issued by the pulse control of motor speed, speed signal by 6221 motor and display card back)
发脉冲
- 电机测试，测试电机的速度，并将速度的反馈曲线存到数据库中(motor testing by FPGA project)
步进电机控制
- 能够使用arduino uno r3来通过步进电机控制器，实现步进电机旋转角度及旋转速度的控制(Arduino uno R3 can be used to control the rotation angle and speed of stepping motor by stepping motor controller.)
关于LabVIEW的一些程序
- 伺服电机控制 Modbus命令帧生成程序. 波形记录 数据的采集与显示 串口通讯 PID控制(Servo motor control. Modbus command frame generation program. Waveform recording. Data collection and display. Serial communication. PID control.)
LabVIEW控制步进电机
- 通讯控制步进电机的行程，速度，延时及循环次数(Communication controls the travel, speed, delay and cycle times of stepping motors.)
H-Bridge & Motor demo
- 基于labview的电机控制程序，亲测能够使用(Motor control program based on LabVIEW)
基于LabVIEW的电机控制系统
- 基于LabVIEW的电机控制系统。包括：直流电机闭环，永磁同步电机控制，电机转速调试，步进电机控制，电机调速器等。适合相关从业人员交流学习。(The motor control system based on LabVIEW. Including: DC motor closed-loop, permanent magnet synchronous motor control, motor speed debugging, stepper motor control, motor governo
拉力传感器电机控制
- 数据采集卡采集拉力值，与预先设定的拉力值进行比较，然后PID运算，控制相应的PWM占空比输出，最终控制电机的速度(The data acquisition card collects the pull value and compares it with the pre-set pull value. Then the PID arithmetic is used to control the output of the corresponding PWM duty cycle, and fin
步进电机的控制(Arduino)
- 用Arduino Uno实现对步进电机转角的控制(Using Arduino uno to control the rotation angle of the stepping motor)
20NO.9伺服电机采集存储
- 基于labview平台，模拟仿真伺服电机信息采集储存(Based on LabVIEW platform, simulate servo motor information acquisition and storage)