搜索资源列表
ourdev_608886TMXLKE
- stm32的led闪烁,一直闪啊闪的,用固件库实现-stm32 the led flashes, has been ah flash flash with firmware library implementation
2501
- 这是用松翰2501B写的一个遥遥棒程序,可显示LED闪字。希望对大家有帮助-This is used Sonix 2501B Writing a distant rods procedures, can display the word LED flash. Hope everyone has to help
led
- 这是一款PIC12F系列单片机闪灯学习程序-This is a learning process PIC12F Flash microcontroller family
shansuodeng
- 基于lpc2103的led闪锁灯的实验 完整版 加开发资料及程序-Lpc2103' s led on the lock lights flash full version plus development of experimental information on procedures for
PISCA_COM_INTER
- Flash led pic18f4550 with interrupt
jiaoxuedalingxitong
- 用LED数码管显示时、分、秒时间,尽量减少时间积累误差,具有秒闪功能。 最多能设置40个打铃时间点,打铃时间点数据用非易失存储器存储,防止掉电丢失数据;能逐个检查、修改、删除已设置的打铃时间点和增加打铃时间点。 对时、打铃时间点用键盘设置,键盘设计简单、易于操作。 具有强电驱动功能,便于控制220V的电铃。-LED digital display with hours, minutes, seconds, to minimize the time error accumulation
pwmled.c
- flash led with PWM with AVR
checkmail
- Program that the scroll-lock LED starts flashing when it detects new email available. You learn howto flash a keyboard LED and how to detect new email. Very handy sourcecode for expanding your own program!
S14-4-P0-eight-LED-flash-20-times-
- S14-4P0口8个LED闪烁20次(子程序设计)-S14-4 P0 mouth eight LED flash 20 times (procedure design)
msp430x20xx_dco_flashcal
- // Descr iption: This code re-programs the F2xx DCO calibration constants. // A software FLL mechanism is used to set the DCO based on an external // 32kHz reference clock. After each calibration, the values from the // clock system are read ou
EMC
- 感应接收到信号后,LED闪灯6次,待机状态每秒闪3次,灯亮30分钟,在此时间内感应,熄灯优先。-After receiving the signal sensor, LED flash 6 times, standby blinks three times, lights for 30 minutes, during this time sensing lights precedence.
test2
- STM32 里面包含各种实验程序,LCD,LED,FLASH,PWM,24C02,WDOG等等,各种程序应有尽有-STM32 contains a variety of experimental procedures, LCD, LED, FLASH, PWM, 24 our fleet, WDOG, etc., all kinds of programs
labview_LED-flash
- labview控制LED闪烁,闪烁时间可调-labview contol a LED for flash,you can adjust delay time
include
- 中断程序的编写:在单片机系统的p1口上接有8个LED,LED的阳极接+5V,阴极接P1口的引脚。当P1口某一口线输出为0时,将LED点亮。在外部中断0输出引脚P3.2引脚上接上上拉电阻并接有一个按钮开关K1。用K1按钮来产生外部中断0的输入信号。定时器程序的编写:在AT89S51单片机的P1口上接有8个LED.下面采用定时器T0的方式一的定时中断方式,使P1口外接的8个LED每0.5秒闪亮一次。C51程序:在AT89S51的P1.0脚接有一只发光二极管,二极管的阴极接P1.0脚,阳极通过限流电阻
led-(2)
- 1-1-2d1,d2同时闪烁6次,之后d1,d2交替闪烁3次后停止,停止时d1,d2熄灭-After the 1-1-2 d1, d2 and flash 6 times, d1, d2 flashing 3 times after stop, stop the d1, d2