搜索资源列表
hongwai_jiema
- 该小制作所需要的元件很少:单片机TA89C2051一只,RS232接口电平与TTL电平转换心片MAX232CPE 一只,红外接收管一只,晶振11.0592MHz,电解电容10uF4只,10uF一只,电阻1K1个,300欧姆左右1个,瓷片电容30P2个。发光二极管8个。价钱不足20元。 电路原理介绍: 主控制单元是单片机AT89C2051,中断口INT0跟红外接受管U1相连,接收红外信号的脉冲,8个发光二极管作为显示解码输出(也可以用来扩展接其他控制电路),U3是跟电脑串行口RS232
SPCE061A_MAX_Sub_good
- 凌阳子程序大全+++趣味语音识别程序+++61板自检程序+++语音电子钟程序+++语音识别且识别过程在图形液晶显示模组LCD上显示实验+++复读机程序+++数据传送指令演示程序+++冒泡排序程序+++LED键盘模组自检程序+++led单向循环流水灯程序+++点亮IOA口外接LED键盘模组的不同的led来显示按键输入值+++外部中断实验+++触键唤醒实验+++IRQ5,4,6时基信号中断实验+++定时器实验+++定时器A/B的irq0、irq1和irq2中断实验+++双路DAC实验+++ADC转换
LEUP1
- 程序 DEMOCRW 和 DEMOPRO 是用于学习 80X86 CPU 的保护模式特性,核心都在常规内存中,方便查看内部数据和堆栈。 本程序必须运行在纯 DOS 下(如 Windows 98 的 启动 DOS ),运行后驻留内存,再运行 DEBUG 实验。 出现保护异常会用黑底黄字显示当前信息(错误代码、中断号(实际是中断号*4)、V86 堆栈)并退出异常程序。 启动时会报告各数据的地址,以及再要显示报告数据的程序地址。 2 RDRXSGEE 程序原为用于 STC89C5
UART
- 单片机通信代码,UART接收和发送数据,通过串口调试发送一个数据然后MCU返回数据到PC端的串口调试器-the mcu can recieve and send a data from uart
1602YEJINXIANSHI
- LCD1602液晶显示从单片控制的串口传输过来的数据的c程序代码-C program code LCD1602 LCD monolithic control over serial transmission of data from
COM2LPT
- AT89C2051针式打印机驱动模块,将2051串口接收到的数据转换后发送到连接打印机的并口上。-AT89C2051 dot matrix printer driver module, after the 2051 serial convert the received data is sent to the printer s parallel port connection.
led
- 利用单片机串行口,实现两个实验台之间的串行通讯。其中一个实验台作为发送方,另一侧为接收方。发送方读入按键值,并发送给接收方,接收方收到数据后在LED上显示-Use of single-chip microcomputer serial port, the realization of serial communication between the two test bench. One of the test bench as the sender, the other side of the
experiment_4_uart_communication
- 这是一个uart串口通信的代码,是基于ise运行的verilog语言,可以实现上位机和开发板的通信以及开发板显示数据并返回累加和的功能。- This is a serial code for uart communication is based on running ise verilog language, you can achieve PC and development board communications, and development boards to display
untitled
- MATLAB中GUI控制串口打开的文件,可以发送和接收单片机数据-MATLAB prepared by the use of GUI control serial port to open the file, you can send and receive microcontroller data
chuankouSerialPort
- VC++编程,串口接收数据并实时波形显示-VC++ programming, serial port to receive data and real-time waveform display
DATACOM
- 基于MSComm控件的PC串口通信原程序,利用中断方式接收数据 -MSComm control PC-based serial communication original program using interrupt receiving data
wendushujuxianshi
- VC++的MFC开发串口调试助手源代码,包括数据发送,接收,显示制式等 -VC++ of MFC development of serial debugging assistant source code, including data transmission, reception, display formats, etc.
usarttend
- 无线数据传输,ARM系统通过串口发送数据到无线模块,无线模块发送数据到计算机-ARM SOFT
a41
- 甲机将片内RAM 30H-4FH的数据从串口发送出去,要求使用校验,BR采用9600bps或4800bps,可以使用按键切换BR,发送完毕后有一颗LED点亮指示- A machine 30H-4FH RAM data the serial port to send out, requiring the use of calibration, 9600bps using BR or 4800bps, you can use the button to switch BR, after
64-Calculator
- 采用4×4键盘,16个键依次对应0~9、“+”、“-”、“×”、“÷”、“ ”和清除键。可以进行小于255的数的加减乘除运算,并可连续运算。当键入值大于255时,将自动清零,可以重新输入。反转法扫描键盘,串行口数据输出,74ls164驱动数码管显示 P1口为扫按键特征码输入端 P3.0,P3.1为串行口数据输出端连接串行静态显示模块的DIN、CLK端。-Using 4 4 keyboard, 16 key corresponding to 0 ~ 9+ in turn- and clear