搜索资源列表
DS18B20
- 可以对温度进行自由设定,到那时必须在0-100摄氏度单位内,设定时可以适时的显示说设定的温度值,温度是可以自由设置的,传感器的检测值与设定的温度比较,可以显示在七段发光二极管上-The temperature can be set freely, then the unit must be 0-100 degrees Celsius, setting a timely display of said set temperature, the temperature can be freely s
passwordlock
- LCD显示器和4ⅹ4的小键盘,制作一个密码锁。PORT 1 连接到LCD显示器的数据线。PORT 3 的P3.3,P3.4和P3.5分别连接到LCD显示器的控制线。PORT 2连接到4ⅹ4的小键盘,可以输入密码。执行修改密码或是时间的程序时,首先让LCD显示器显示出时间和日期。 当用户按下4ⅹ4小键盘的按钮 A 时,可以输入密码。如果密码正确时,就会让 P3.6的 LED 闪烁,表示打开锁。如果密码不正确时,LCD显示器就会显示出-LCD display and 4 ⅹ 4 small k
ledxianshi
- 51单片机实现led数码管动态显示,用汇编编写-51 MCU led digital tube dynamic display, with the compilation of the preparation
final.asm
- a)实现时钟功能,可以在两个七段数码管上显示秒钟时间或者分钟时间,用一个开关控制两者的切换。 b)实现闹钟功能,时间到播放一段音乐,并在发光二极管上播放走马灯图案,在双色点阵发光二极管上滚动显示自己的学号。能控制滚动显示的速度以及音乐播放的速度,且用一个开关控制闹钟的开关。-a) achieve clock function, can be in two seven-segment digital tube display seconds or minutes, with a switch
naozhong
- 八位显示轮流月日 星期 时间 一个闹钟 四LED显示调节状态-Eight months, weeks display turns a clock
shuxianbiao
- 多功能数显表 本毕业设计的设计任务为一个多功能数显表。该数显表可以测量和显示气压、冲击频率和耗气量。并且具有RS232接口和时间显示。本毕业设计作品选用AK-4气压传感器和LWGY涡轮流量传感器,通过MCS-51单片机来控制操作,实现信号数据的采集、处理和发送。本毕业设计作品不仅可以将气压、冲击频率、耗气量及时间等数据显示在8个LED数码管上,还会通过RS232串口,将数据发送到PC上。并由PC上的配套程序,将信息数据显示在显示器上,这两部分所显示的数据是完全相同的。其中数字显示时间单位为秒
SMG
- 在8位LED数码管上动态显示1,2,3,4,5,6,7,8-In the 8-bit LED digital tube dynamic display 1,2,3,4,5,6,7,8
K7
- 将36位BCD数转换成ASSCII十进制数,以BCDBUFF为首地址的内存区中存有18个字节的组合BCD数,要求转换为相应的36个ASCII十进制数,并依次输出到CRT显示。BCD数存放时,低位在前,高位在后,例如,若BCD缓冲器内容12H,34H,56H,78H,...12H,56H,78H,则要求CRT上依次显示以下36个数字: 785634......563412-To 36 BCD digits into ASSCII decimal to BCDBUFF led address m
keybd
- 利用中断方式响应键盘输入,并识别是哪个键按下。用两组4个LED显示被按下键的的行编号与列编号。-Interrupt in response to keyboard input, and identify which key is pressed. Two sets of four LEDs to display the line number and column number is pressed key.
keyboard
- 基于MCS-89C51的秒表LED数码管显示-Based on the MCS-89C51 stopwatch LED digital display
H8255
- 通过8255实现彩灯控制,由8个LED显示8个开关 的状态:开关 闭合时,则有i个LED灯亮,例如: 闭合时则相应的 、 、 亮; 闭合时则相应的 、 、亮,-Control by 8255 to achieve Lantern, 8 LEDs display the status of the eight switches: the switch is closed, then the i-th LED lights, for example: the corresponding closed
3-4
- 1.从键盘随机输入十个数据,统计其中负数的个数,并在屏幕上显示出来; 2.求出这十个数的总和, 存入数据段SUM 单元,并在屏幕上显示出来; 3.将这些数从小到大排序,存入 ORDER 为首址的存储区域,并在屏幕上显示出来。 4.编一跳转表,按键1,2,3,分别执行上述三种操作。 -1. Stochastic input from the keyboard, ten data, the number of statistical wherein negative, and on
mnppqbs
- 用8个LED发光管(红黄绿)的来回滚动显示来模拟打乒乓球时乒乓球在两边球台上的来回运动。比赛双方用按钮/开关(双方各用一个按钮/开关)来模拟发球与接球,即发球方按动其控制的按钮/开关,球从发球方一侧向另一方运动(LED发光管从发球方到对方逐个点亮,滚动显示),当球运动至接球方时,接球方立即按动其控制的按钮/开关,“击球”使球“弹回”发球方一侧,如此周而复始,直至在规定的击球时间内有一方未能完成击球动作,从而对方的一分,然后继续比赛。比赛规则可参照一般的乒乓球比赛规则。 (1) 球以每0.5秒
Traffic-light-control-system
- 编写一个交通灯控制程序,实现东西路口与南北路口状态灯的转换和紧急处理。采用8253芯片计数,输出1S的时钟脉冲,并使用8255接口芯片控制LED亮灭,同时让8279芯片显示倒计时,键盘控制紧急处理按键,以此实现交通灯指挥控制系统。-Write a traffic light control program, the conversion of the things the intersection with the north and south of the intersection stat
DS_PIC16F883_Led_Panel_74ls164
- PIC16F883使用74ls164驱动LED数码管的程序,使用3个脚可以控制8个LED数码管的显示,同时将TRC芯片ds12887的时钟内容显示出来-The PIC16F883 to use 74ls164 drive LED digital tube procedure, the use of 3 feet can control of eight LED digital tube display, at the same time the the TRC chip clock ds1288
PIC16F883_bq3287_CLOCK
- PIC16F883使用74ls164驱动LED数码管的程序,使用3个脚可以控制8个LED数码管的显示,同时将TRC芯片BQ3287的时钟内容显示出来,附仿真电路。-PIC16F883 use 74ls164 drive LED digital tube procedure, the use of three feet can control of eight LED digital tube display, while the the TRC chip BQ3287 clock display
jiaotongdeng
- 运用汇编语言在x386 系统上利用彩色led模拟交通灯管理系统,加入倒计时显示和紧急开关-The use of assembly language x386 systems using color led simulated traffic light management system, adding countdown display and an emergency switch
8086-8255
- proteus仿真8086控制led矩阵,显示多种花色,可用来作课程设计。-proteus simulation 8086 control led matrix display a variety of colors, and can be used for curriculum design.
ledjuzheng
- 8086,和8255实现led矩阵显示多种花色,含proteus仿真-8086 and 8255 led matrix display a variety of colors, including proteus simulation
pingpangqiu
- 电子乒乓球模拟比赛,用8个LED发光管(4红4绿)的来回滚动显示模拟打乒乓球时,乒乓球在两边球台上的来回运动。比赛双方用按按钮(双方各用一个按钮)的方法来模拟发球与接球,即发球方按动其控制的按钮,球从发球方一侧向对方运动(LED发光管从发球方到对方逐个点亮,滚动显示)。 当球运动至接球方时,接球方立即按动其控制的按钮,“击球”使球“弹回”发球方一侧。如此周而复始,直至在规定的击球时间内有一方未能完成击球动作,从而对方得一分;然后继续比赛。 -Electronic Table Tennis