搜索资源列表
beepled
- 发光二极管&LED显示程序清单 方波输出以及BEEP蜂鸣程序清单
pinlvjichange
- 测量频率范围:0~5KHZ,测量结果由LED显示; 基本频率上限3KHZ,下限10HZ,超出范围点亮L9报警; 上、下限可通过按键调整。 -measurement frequency range : 0 ~ 5KHZ, the measurement results from the LED display; 3KHZ fundamental frequency cap, minimum 10 9999, outside the scope of lights to install
yxcvcxvcxbvcx
- (红外线遥控)将万能遥控按键的键值通过At89s51P1口的8个LED显示出来-(infrared remote control) Universal remote control keypad keys through the At89s51P1 I was eight LED said out
DIY_LED_BMP
- (转载)本电路利用LED发光管组成点阵式来显示图案-(reproduced) the use of LED circuit composed of dot-matrix display pictorial
xmlLED
- 自己做的LED汇编程序,是帮同学做的课程设计-own LED compilation procedure is done to help the students design the curriculum
conection
- 用8255新片连接输入输出电路,输入设备是一组(8)个开关,输出是一组(8个)LED灯,写程序,在搬动开关时,使LED灯按某种规则变化(自己定义) -8255 with a new film linking the input and output circuit, input equipment is a group (8) switching, Output is a group (8) LED lights, write procedures, the moving of the swit
arm_led
- ARM LED control Assembly example-ARM Assembly example LED control
LEDmove
- 点阵LED多字移动程序,很好用的,可以应用到其他类似的程序中
MAX72197211
- 串行LED显示驱动器MAX7219 7211应用程序.ASM-serial LED display driver MAX7219 7,211 applications. ASM
DOT16x16
- 16 x 16 LED problem for display use can run dynamically-16 x 16 LED problem for display use can run dy namically
LED82
- 8051进行8路LED模拟分支控制 用8051的P1口作为输入、P0口作为输出,通过74LS244接8路LED模拟分支控制。 P1.0为低电平时,点亮一LED;P1.0为高电平、P1.1为低电平时点亮全部LED;当P1.0、P1.1都为高电平时,LED按四个一组,轮流反复点亮 P1.0、P1.1、P1.2都为高电平时,8LED逐一点亮并反复循环 -8,051 for eight LED branch control simulation using 8051 as input
LEDDENG
- LED灯,1片89C51两片595+4片LED灯程序-LED lights, a two 89C51 595 four LED lights procedures
TRAFFICLIGHTS8255
- 交通信号灯的控制: 1. 通过8255A并口来控制LED发光二极管的亮灭。 2. A口控制红灯,B口控制黄灯,C口控制绿灯。 3. 输出为0则亮,输出为1则灭。 4. 用8253定时来控制变换时间 。 要求:设有一个十字路口,1、3为南,北方向,2、4为东西方向,初始态为4个路口的红灯全亮。之后,1、3路口的绿灯亮,2、4路口的红灯亮,1、3路口方向通车。延迟30秒后,1、3路口的绿灯熄灭,而1,3路口的黄灯开始闪烁(1HZ)。闪烁5次后,1、3路口的红灯亮,同时2、4路口的
shuzinaozhong
- 具有按键控制,时间可调,可设定闹钟时间,LED显示-with button control, adjustable time, set alarm clocks, LED Display
huibianyinyuefashengchengxu
- 音乐发生程序,程序中有两首歌,并且在播放的同时由LED显示所播放的音乐-music occurred procedures, procedures have two songs, and the broadcast of the show by the LED broadcast music
8031LED
- 8031直接驱动LED的电路 以下是利用8031的I/O口直接驱动LED的电路原理图。电路通过8031的P0、P2口连接一片74LS373和一片27128构成外拓存储器,通过P1口直接连接LED,驱动显示器,通过P3.0、P3.1、P3.2、P3.3连接电平开关S1、S2、S3、S4作为逻辑输入控制。
temp
- 温度测量系统源码 通过A/D0809数模转换 LED显示温度
jiekoulcd
- 1.将LED模块的CSLED接8088地址的200H。 2.编译原文件,连接并全速运行。 由8279处小键盘按下 Key 1 欢迎使用AEDKT598实验台 Key 2 圣诞快乐 Key 3 新年愉快 Key 4自左à右逐列显示“各位同学好”
liushuixian
- 51控制led顺序点亮, 通过控制p0.0使其能按不同的顺序
ADandDISPLAY(ASM)
- 把AD转换的数据在LED上显示,可以显示四位数字