搜索资源列表
serial1
- 串口简化verilog模型，固定波特率4.8k, 输入、输出使能输出-Verilog model of serial simplified
async_transmitter
- 该程序为RS232串口通信的VERILOG程序，在FPGA上已通过验证，在测试范围内误码率为0-The program for the RS232 serial port communications VERILOG procedures, the FPGA has been validated in the test range of bit error rate is 0
SPI_VERILOG
- SPI串行总线接口的Verilog实现.pdf 通过FPGA实现-The Verilog implementation of the SPI serial bus interface. Pdf FPGA implementation
ser_adder
- 串入串出加法器 verilog 代码 串入串出加法器 verilog 代码-serial adder verilog code serial adder verilog code
FPGA_uart
- verilog 编写的FPGA串口通信的代码，可实现串口的收发操作-FPGA serial communication code written in verilog serial transceiver operation
CPLD_18b20_uart
- 温度传感器采集数据给cpld，然后由串口上传到上位机；编程语言是verilog；-Temperature sensor collected data to the the cpld, then uploaded to the host computer by serial programming language verilog
SerialPort_RxTx
- verilog 简单易用，占用资源少。 串口收发模块。-verilog .Serial port receive & transmition module
UART
- 基于ISE 用verilog编写的uart串口通信源码-Based on the ISE written in verilog uart serial communication source code
verilog-uart
- UART（Universal Asynchronous Receiver Transmitter，通用异步收发器）是广泛使用的异步串行数据通信协议。下面首先介绍UART硬件接口及电平转换电路，分析UART的传输时序并利用Verilog HDL语言进行建模与仿真，最后通过开发板与PC相连进行RS-232通信来测试UART收发器的正确性。-UART (Universal Asynchronous Receiver Transmitter, Universal Asynchronous Receive
chuankou7883
- 串口AD的FPGA实现，为verilog程序，芯片为7883，编译已通过-Serial FPGA implementation of AD for verilog program for the 7883 chip, the compiler has passed
spibus
- serial peripheral interface bus in verilog
verilog_RS232
- 基于FPGA的Verilog硬件描述语言的串口通信设计，非常适合初学者和正在开发的人员使用，参考。-Descr iption Language Verilog FPGA-based hardware serial communication design, ideal for beginners and are being developed to use and reference.
uart
- 该模块是基于串口协议用verilog实现了串口的接收和发送功能。-The module is based on a serial port protocol using verilog to realize the function of receiving and sending of the serial port.
基于FPGA的串口通信系统
- 该设计是基于 FPGA 的串口通信系统模拟仿真，通过对 RS-232 串行总线 接口的设计，掌握发送与接收电路的基本思路，并进行串口通信。采用 Verilog HDL 语言对 UART 波特率产生模块、数据发送模块、接收模块进行硬件描述， 再将其整合为一个 RS-232 收发模块，最终在顶层模块中将两个 RS-232 模块例 化，实现两块 FPGA 芯片全双工通信的设计。(Design of serial communication system based on FPGA)