搜索资源列表
Driver_AS3992RFID_for_ARM
- ARM开发板直接驱动基于AS9332芯片RFID模块的相关程序和函数节选。在STM32F107开发板上调试运行通过。演示程序已经支持4.3’LCD触摸屏、8GMicroSD卡、EEPROM、2M的Flash SST25VF016B，支持两个串口、一个SPI，还有按键、LED,有实时时钟等，软件功能有文本浏览、图片浏览、画板，以及RFID读写。-Driver AS9332 RFID module for ARM
LPC177x_178x_UM_SimpCHN
- 基于ARM Cortex-M3的微控制器LPC177X/178X,简体中文版用户手册，1788等多款型号内带LCD看控制器最高支持分辨率1024*768-Based on the ARM Cortex-M3 microcontroller LPC177X/178X, Simplified Chinese version of user manual, 1788, various models with LCD to see the controller supports up to 1024*
111
- 1 .手机屏幕尺寸为 w = 240 h = 320，现提供LCD BUF(type:unsigned short)的起始地址为lcdbuff。要求从坐标(100,10)处开始绘制一条长度为300的黑色(颜色值为0)垂直线。 参考代码： 2 .在第1题的基础上封装一个画垂直线的函数，不考虑颜色。 参考代码： 3 .在第1题的基础上封装一个画水平线的函数，颜色可不考虑。 参考代码： -The start address of a mobile phone scr
123
- 本文设计了以AT89S52单片机作为控制器，LCD液晶和矩阵键盘为互动模块，射频技术基础，应用飞利浦公司MF-RC500芯片作为读写IC的载体，并可以与上位机进行串口通信的非接触式IC卡读写器。-Designed microcontroller AT89S52 as the controller, LCD LCD and matrix keyboard interactive modules, RF technology base, application of the Philips MF-R
jianyixindiantu
- 本设计才用低功耗16bit单片机MSP430F2274作为整个控制核心，利用低噪声，低功耗，有良好共模输入抑制能力的仪表放大器INA2331。带人机LCD接口。实现心电图测量。-This design only with low-power 16bit microcontroller MSP430F2274 as the control core, low noise, low power consumption, good common mode input rejection of the
1602
- LCD1602液晶显示的程序，实现了一些功能。-LCD1602 LCD program, some of the features.
1602andADandDA
- 51单片机1602液晶加串口加ad加da编程资料合集-51 MCU 1602 LCD plus serial programming plus ad plus da data collection
MTB-255
- mtb-255 cog lcd config
DS12887-DS18B20
- 多功能时钟的程序，能用18B20测试并显示温度，LCD显示时间-Multi-function clock program, can 18B20 test and display temperature, LCD display time
OGM-12864FL
- 128X64 LCD DISPLAY SPECIFICATIONS TECHNICAL DATA
LCD1602
- LCD的一个显示程序，使用protues模拟-The LCD display program, use protues analog
s3c2440_LCD
- LCD驱动原理及寄存器控制详解，有示例程序~！~！-LCD driver
OneWire
- This code demonstrates one-wire communication with temperature sensor DS18x20 connected to RD0 or RA5 pin. unit reads temperature from the sensor and prints it on the LCD. The display format of the temperature is xxx.°C . To obtain correct
P16F873
- A simple example of using the keypad library for mikroC PRO for PIC. It supports keypads with 1..4 rows and 1..4 columns. The code being returned by the Keypad_Key_Press() or Keypad_Key_Click() functions is in range from 1..16. In this exam
FPGA-TFT
- FPGA 实现的 TFT 液晶屏控制方案！希望对你有帮助！-FPGA Implementation of TFT LCD screen control scheme!
arm11_s3c6410_program_note.tar
- 基于arm11架构的s3c6410处理器的编程笔记（GPIO、INTERRUPT、CLOCK、WATCHDOG、PWM、DDR、NAND、LCD、ADC、DM9000）-Based on the the arm11 s3c6410 processor architecture, programming notes (GPIO, INTERRUPT, CLOCK, WATCHDOG, PWM, DDR, NAND, LCD, ADC, DM9000)
yejingpingsheji
- 本篇文章介绍了液晶屏的设计，从传统指令方式读写改为总线地址方式读写，具有一定的参考价值。-This article introduced the LCD screen design, from the traditional command mode read/write to address bus read and write, has a certain reference value.
LC
- 本系统是以FPGA（EP2C8Q240C8）为控制核心，由压控振荡器、PLL倍频器、高频功率放大器、遥控器及LCD显示模块组成的压控LC振荡器。能实现输出正弦波频率在15MHZ~35MHZ步进可调，其最小步进为5002HZ，频率稳定度为10-5。当输出信号的频率为30MHZ、峰峰值稳定在1V左右时，在+12V单电源工作的情况下，功率放大器能实现在50Ω纯阻性和50Ω+20pf容性负载上输出功率大于20mw。LCD显示模块能实时显示输出信号的峰峰值和频率，精度由于10 。-This system
DS18B20
- 基于单片机的数字温度计设计，即对温度进行实时测量，使用单线数字温度传感器DS18B20把温度信号直接转换成数字信号输入单片机。经单片机处理后，将实时温度显示LCD液晶显示器上。-Based on SCM digital thermometer design, namely temperature in real time measurement, use wired digital temperature sensor DS18B20 temperature signal directly co
trade520
- 单片机C语言程序设计实训100例/新手练习程序有流水，LCD，点阵，A/D，中断，音乐，计算器，数码管等-100 cases of single-chip C Programming Language Training/novice exercise program there is running water, LCD, dot-matrix, A/D, interrupts, music, calculator, digital tubes, etc.