搜索资源列表
pwm
- 直流电机驱动芯片采用Ｌ２９８．支流电机驱动就是利用ＰＷＭ脉宽控制Ｌ２９８电流输出大小，从而达到控制电机的目的-Motor Driver IC using L298. Tributaries is the use of motor-driven PWM pulse width control L298 current output size, so as to achieve the purpose of the electrical control-DC motor driver chip L2
sourceprogram
- 篮球计时器，键盘扫描，步进电机的控制，交通灯，及其温度计-Basketball timer, keyboard scanning, stepping motor control, traffic lights, and the thermometer
Fuzzy_PID_Control_of_Stepping_Motor
- 摘要:由于步进电动机调速系统具有非线性等特点,使得利用简单模糊控制与传统PID控制精度不高,因此文中提出利用模 糊PID控制器实现对步进电动机调速系统进行控制的方法,并设计了模糊PID控制器。文中首先建立了步进电动机的数学 模型,并根据数学模型推导了其传递函数 然后介绍了模糊PID控制器结构,以及模糊控制规则的生成方法,并且对该控制 方案进行数字仿真。仿真结果表明:该方法调节精度较高,动态响应快,无超调,有一定的可行性。 -Abstract: As the stepper mot
pundulum1
- 单级倒立摆的稳定控制，实际上是一单输入多输出系统的稳定控制。此时系统输入是电机控制电压u，输出是倒立摆竖直方向角度 和旋臂位置 。对方程(2.5)进行变形即得 与u 之间的输入输出方程,很明显,它是一个不稳定的二阶系统-Single inverted pendulum stability control, is actually a single-input multiple-output system stability control. At this point the system is
motor
- 51系列单片机驱动步进电机控制系统电路及程序-51 series stepper motor drive circuit and program control system
73462674kaihuan1
- dc motor spped control
step
- 基于89C51单片机的四相六线步进电机控制系统，可以按键实现电机的起停，正反转及三级速度控制，并有led灯指示-89C51 microcontroller based four-phase six-step motor control system that can achieve the motor start and stop buttons, Reversible, and three speed control and have led indicator light
bi huan shen jiang tai
- 无线遥控的速度稳定的直流电机升降机电路原理图及电路板图（DXP2004版）-Wireless remote control DC motor speed stability and lift the circuit board schematic diagram (DXP2004 Edition)
DoubleLoopDCSpeedControlSystemSimulation
- 本文说明了双闭环直流调速系统仿真设计，详细地介绍了基于Matlab的仿真过程。-This article describes the two-loop DC motor control system based design, detailed descr iption of the simulation based on Matlab.
control
- control of ac and dc motor using fussy logic-control of ac and dc motor using fussy logic
PWM
- 关于各种电机的PWM程序： 工程1，采用C语言完成的主要功能有 1：用定时器1中断让LED闪烁； 2：用定时器2的比较单元产生一路PWM； 3：用EVB模块产生6路PWM； 另外四个汇编程序依次分别是： SVPWM（软件法）程序， 交流异步矢量程序， 直流双极性双闭环可逆控制程序， 和采样SPWM程序。 -PWM motor on a variety of programs: Project 1, using C language to complet
A040103C
- Backstepping Control based on Lyapunov Theory for Sensorless Induction Motor with Sliding Mode Observer
ARM
- 设计一个电动机控制器，两台电动机的控制要求为：当按键k1按下后，第1台电动机运转5s后停止，切换到第2台电动机运转，10s后第2台电动机自动停止运转。-Design a motor controller, two motor control requirements: When the button is pressed k1, 1 5s electric motor stops running, switch to 2 motors running, 10s after the first 2
bujindianji
- 步进电机的控制原理，采用达林顿驱动器与单片机相连的原理图，以及步进电机的控制程序，都是用通俗语言讲述的，希望有所帮助。-Stepper motor control principle, the use of Darlington connected to the microcontroller drives the schematic, and stepper motor control program, are described in simple language, I hope help
yibudianjishiliangkongzhi
- 异步电机无速度传感器控制仿真 里面说的很详细 主要是模型参考自适应-Induction motor speed sensorless control simulation which is mainly that the very detailed model reference adaptive
MOTOR-8051-MICRO-CHIP-C51-CONTROL
- 电动机单片机控制C51程序设计，综合单片机、C语言、电动机控制三大技术，使工程技术得心应手-MOTOR 8051 MICRO-CHIP C51 CONTROL
zhiliudianji
- 基于伟福6000的直流电机控制系统，通过键盘控制改变电机运动状态-Wei Fu 6000 based DC motor control system, controlled through the keyboard to change the electrical state of motion
123
- 永磁无刷直流电机控制技术Permanent magnet brushless DC motor control-Permanent magnet brushless DC motor control
213
- Permanent magnet brushless DC永磁无刷直流电机控制技术应用-Permanent magnet brushless DC motor control technology
Control_of_Induction_Motors
- induction motor control