搜索资源列表
TEMP_AD_DISP_SPI
- 利用NTC低价热敏电阻做的温度表,程序中使用二分法查表,SPI送数据到LCD显示,选好充放电电容时室温误差在0.5摄氏度左右.-Use of low-cost NTC thermistor thermometer to do, look-up table used in the program dichotomy, SPI sending data to the LCD display, choose a room temperature charge and discharge capacit
temp
- 51利用电阻电容充放电进行温度测量，C语言，成本低-51 the use of resistance and capacitance charging and discharging the temperature measurements, C language, low cost
pic16c54temp
- 基于PIC16C54的测温代码，C语言，测温范围-50到110度，电阻电容充放电测温，无需AD-The temperature measurement based on PIC16C54 code, C language, temperature range of-50 to 110 degrees, the resistance and capacitance charge and discharge temperature, no AD
soft_ad
- 利用电容充放电的特点，使用单片机和简单的电容电阻，实现纯软件方式的AD转换。-Using capacitor charging and discharging characteristics, and simple to use single chip capacitors resistors, way to achieve pure software AD conversion.
FPM-SHIELD-01R
- 这是一个电子称的全部文档，包含原代码，流程图，参数表等。该电子称采用双积分方式进行采样测量，为了保证测量准确，双积分采用正反方式对电容进行充放电，实践证明，该方法效果可靠，精度高，已大批量生产-This is an electronic call all the documentation, including source code, flow charts, tables and other parameters. Double integration of the electronic m
CapacitorLife-ST7920-4
- 交流启动电容寿命测试控制程序，控制10个电容，充放电，并进行计数。-AC start capacitor life test control procedures, control of 10 capacitors, charge and discharge, and counting.
test1
- 湿度控制,基于51单片机的电容充放电式的湿度控制显示模块-temp controul
chongfangdian
- 充放电用大电容实现具有参考意义其中二极管的作用可仔细研究-With large capacitors charge and discharge with reference to the role of meaning in which the diode can be carefully studied
ch2example9prg1
- 这是应用ｍａｔｌａｂ模拟电容充放电的过程，编写一段程序，希望对大家有用。-This is the application matlab analog capacitor charging and discharging process, the preparation of a program, in the hope that useful.
d4ef13.ZIP
- Buck变换器动态过程电容充放电平衡控制策略Buck converter dynamic process of capacitor charging and discharging balance control strategy-Buck converter dynamic process of capacitor charging and discharging balance control strategy
STM8-touch-program-without-library
- STM为了卖产品做出的库实际是将简单的问题复杂化，你要是用调用STM8的所谓TOUCH库的方法设计触摸按键，那各种绕弯十万八千里的调用能把你头搞炸。RC电容触摸按键的检测原理其实很简单，而具体到STM8单片机上则是通过所谓的LOAD脚加载高、低电平进行充、放电，然后检测键盘脚的高低电平的门限Vih、Vil以及读取定时器而获得充放电的时间。具体可到www.stmcu.org获取相关资料。-STM library in order to sell products to make the actua
gukh
- matlab仿真。matlab进行超级电容充放电的闭环控制。-matlab simulation. matlab super capacitor charging and discharging of the closed-loop control.
SONiX
- 松翰单片机低成本利用I/O口和电阻电容的充放电测温。-Sonix MCU low-cost I/O port and a resistor-capacitor charge and discharge temperature measurement.
CRL
- 电容充放电产生方波,再经积分器转成三角波,再经微分器转成方波-Capacitor charging and discharging generate a square wave, and then by the integrator into a triangular wave, and then turn a square wave differentiator
labview-capacity
- labview vi程序，基于版本8.2可以直接运行，,用来仿真电容充放电过程-labview vi program, based on version 8.2 can be run directly, to simulate capacitor charging and discharging process
main
- STM8的一个设计型电路，用于设计一个超级电容的充放电电路-STM8 of a design type circuit for the design of a super capacitor charging and discharging circuit
current_1_capacitor
- 超级电容充放电测试，能够都实现超级电容的横流充电和横流放电，观测超级电容的端电压-the test of supercapacitor charge or discharge
cap
- 本代码是基于STC89C52单片机最小系统开发环境的测量未知电容电路。根据555定时器的不同电容充放电时间得到未知电容值。-The code is based on the STC89C52 MCU minimum system development environment for the measurement of unknown capacitance circuit. According to the different capacitor charge and discharge t
电容
- 充电量与放电量，显示所充电的电量最大与放电量所达到的最小，并且可以显示波形图(Charge and discharge, show the maximum amount of charge and the minimum discharge amount, and can display the waveform diagram)
电容充放电检测小电解
- 小电解电容充放电单片机检测，利用RC充放电时钟原理(small capicitence test by 51MCU)