搜索资源列表
红外遥控六足爬虫机器人设计
- 红外遥控六足爬虫机器人设计.有详细的文档，包括电路图和代码-design for infrared remote control to robots with six legs ,which has detail text including circuit and code
红外遥控系统原理及单片机软件解码实例
- 本文介绍了红外遥控系统的通信原理和系统构成，并给出了原理图及部分编程代码。
34534343434
- 采用实时时钟芯片DS1302+AT89C2051的红外遥控LED电子钟(原程序沈洁代码.rar-using real-time clock chip DS1302 AT89C2051 infrared remote control LED electronic bell (the original Shen Jie procedure code. rar
HONGWAI-C
- 红外遥控的C51 代码 ，比较实用的参考程序-Infrared remote control code of C51, the reference to the procedure more practical
51code
- 51开发板上的源代码程序，里面有DS18B20液晶1602显示温度和控制代码，lcd1602时间显示c 程序代码，lcd 1602液晶显示代码，lcd12864字库显示代码，24C02存储器I2C总线代码，还有红外遥控接收和读码代码。-51 the development of on-board procedures for the source code, there are DS18B20 LCD temperature display and control the 1602 code,
zju-61MCU-code
- 本文件夹包含浙江大学信电系暑期电子设计培训时以及校赛时的几个项目的代码，包括波形发生器，集成运算放大器，简易数字显示声音信号采集测量仪的设计，数码管红外遥控显示，温度测量PWM模拟控制LED等。采用的单片机为凌阳SP061A单片机。-This folder contains a letter, Zhejiang University, Department of Electrical Electronic Design training in the summer and school even
Electronic_Code_Lock
- 电子密码锁，包含电路图，程序代码，还有红外遥控的解码部分-Electronic lock, including schematics, program code, as well as infrared remote control decoding part of the
hongwaiduoluyaokong
- 本文介绍了红外多路遥控系统。红外多路遥控系统可实现16路的红外开关控制。以码分制多通道红外遥控为设计的基本思路。通过键盘及代码生成电路、编码、脉冲调制振荡和红外发射构成红外发射电路。通过红外接收，解码以及由单片机控制的医码控制电路组成红外接收电路。-The passage has introduced the nfrared multichannel system of remote control. The infrared multichannel system of remote cont
Study_IR_Remote_Control
- 资料包含源码，硬件图，红外相关资料等，本学习型红外遥控器，通过学习一次遥控器的编码，即可脱离原遥控器来遥控电器或者设备，源码很完整，严格测试过，不过由于C52的单片机RAM有限，编码缓冲区长度有限，而不同的遥控器的编码长度也不相同，对于像空调遥控器编码比较长的就会出现学习不了的情况，必须要加外部RAM作为接收缓冲区，或者换用STC的单片机，内部的RAM比较大，不用扩展，用STC还有好处就是不需要外部的eeprom来保存读取的编码，而C52需要用外部的EEPROM来保存编码，这个源码实用的AT24
hongwaiyaokong1
- ATMEGA8的红外遥控代码，带显示屏，程序已调试好-ATMEGA8 infrared remote control code, with display, the program has good debugging
hongwaiyaokong2
- ATMEGA8的红外遥控代码，带显示屏，程序已调试好-ATMEGA8 infrared remote control code, with display, the program has good debugging
Infrared--code
- 红外遥控代码，使用于51单片机。代码简单，功能强大。-Infrared remote control code, used in 51 single-chip microcomputer. The code simple, powerful.
HJduino
- 核心板为stm32f103，该小车红外遥控代码是在keil 5 环境下用c语言编写的程序。实验多次，稳定性好，并且有相应注释，可灵活更改相关数据。(Core board for STM32F103, the car infrared remote control code is in the Keil 5 environment, written in C language program. Experiments many times, good stability, and correspo
5.小车红外遥控超声波测距
- 此代码为小车红外遥控超声波测距，基于stm32的(This code for the car, infrared remote control, ultrasonic ranging, based on stm32)
IR_RS232
- 红外遥控代码,需要重新配置SysTick的中断优先级为最高，要不然SysTick延时中断抢占不了IO EXTI中断,或者当你用其他定时器做延时的时候，要配置定时器的优先级高于IO EXTI中断的优先级.(Reconfiguration of SysTick interrupts the highest priority, otherwise SysTick delay interrupts cannot preempt IO EXTI interrupts * because the defa
第61讲 红外遥控器实验-M3
- 利用单片机进行的红外遥控器实验代码详细资料(Microcontroller infrared remote control experiment code details)
led时钟成熟可用代码
- led时钟成熟可用代码,DS321,GPS,红外遥控(LED clock is mature and usable code, DS321, GPS, infrared remote control)
红外
- stm32实现红外遥控代码 使用红外遥控器，实现对stm32版上的特定功能。(STM32 implementation of infrared remote control code The use of infrared remote control to realize the specific functions on the STM32 version.)
红外遥控计算器LCD1602
- 红外遥控，LCD显示，程序代码，PROTEUS仿真(Infrared remote control, LCD display, program code, PROTEUS simulation)
魔改红外舵机
- 红外遥控舵机，具体io口配置见代码内，遥控范围180-0°，可以适宜温度偏差(Infrared remote control steering gear)