搜索资源列表
6.GPIO输出实验-LED数码管
- EasyARM2131开发板源码之一-----------6.GPIO输出实验-LED数码管显示0-F字符，同时控制LED1、LED2、LED3、LED4显示对应的16进行值-EasyARM2131 one source development board ----------- 6.GPIO experimental output - digital LED Display 0-F characters and control LED1, LED2, LED3, LED4 shows the
keyINT
- 44B0的测试程序。此程序为44B0的4*4键盘的应用程序，基于中断0触发，当按下其中一个键时，会把0-F的相应键值显示在8段LED上。-44B0 testing procedures. This procedure for the 44B0 4 * 4 keyboard applications, based on the interruption 0 trigger, which when pressed a button, will be 0-F to the corresponding
显示0到F
- 利用串行驱动数码显示每位从0显示到F，到灭循环显示，要求1秒更新一次。-drive using serial digital display shows each from 0 to F, to eliminate cycle, a request updated seconds.
4X4-KeyBoard
- 用AT89S51的并行口P1接4×4矩阵键盘，以P1.0－P1.3作输入线，以P1.4－P1.7作输出线；在数码管上显示每个按键的“0－F”序号-Parallel port P1 with AT89S51 4 × 4 matrix keyboard connected to P1.0-P1.3 as input lines to P1.4-P1.7 as an output line in the digital display for each button on the " 0-F
lesson3_4
- 利用数码管将显示的数字0-F显示在数码管上，然后循环-The use of digital control will display the number 0-F displayed on the LED, and then loop
anjianxianshi0~F
- 按下小键盘任何一个键，显示相应的字符0~F-Press any button keypad, display the corresponding characters 0 ~ F
display0-F
- C语言程序，点阵循环显示0-f，经过仿真的，附有仿真图和源代码-C language program, dot-matrix cycle through 0-f, through simulation, with simulation diagram and source code. . . .
0-F
- 51单片机中单个数码管从0显示到F的C程序源代码-51 single-chip single digital tube display from 0 to F, C source code. .
display-0-F---for-HJ-52
- STC12C5A60S2+HJ-C52板，8位数码管同时显示0-F-STC12C5A60S2+HJ-C52 board,display 0-F at the same time on both of the 8 SEGs.
led-0-f
- 使用LED静态显示数字和字母,led的使用-Using LED static display of the use of numbers and letters, led
0-f-jianpan
- C51单片机按键显示0-f,通过按键在八段led上显示-C51 MCU button to display the 0-F
0-f-xs
- 用一个led来动态显示从0到9的数和a到f的字母 实现加一计数-add one every time
0-~-F-button-to-display
- 0~F按键显示，矩阵键盘上，每按一个键，则对应显示其十六进制数-0 ~ F button to display
juzhenjianpan0-f
- 基于51单片机开发板，矩阵键盘按键在数码管上显示0~F-Based on 51 MCU development board, matrix keyboard keys on the digital display 0 ~ F
anjianxianshi0~F
- 按下小键盘任何一个键，显示相应的字符0~F-Press any button keypad, display the corresponding characters 0 ~ F
0-F
- 由单片机控制0-F逐个显示，程序简单易懂，易于学习。-Controlled by the microcontroller 0-F-by display, the program is simple to understand, easy to learn.
单片机代码
- 实现0.5秒闪一次，从0开始到f从左到右一次循环，按键程序，奇偶判断等功能(Achieve 0.5 seconds flash, starting from 0 to F, from left to right cycle, button procedures, parity and other functions)
正点原子战舰STM32-LCD12864显示-GPIO全部F口
- 基于stm32单片机开发的LCD12864液晶显示程序(The LCD12864 LCD program based on STM32 microcontroller)
单片机汇编：数码管显示实验
- 1.静态数码管显示（0~F） 2.动态数码管显示:(1)动态显示数字（不用译码器）（1234567）;(2)动态显示数字（带译码器）(An assembler of digital tube display experiment)
矩阵按键数码管移位显示
- 按矩阵键盘分别显示在数码管上面显示十六进制的0到F(According to the matrix keyboard, it shows sixteen to 0 to F on the digital tube respectively.)