搜索资源列表
RS485C
- 用C语言编写的485--MODBUS RTU 通信的小程序.已使用过,希望和大家分享一下.-C language prepared by the 485 -- MODBUS RTU communications small programs. Have used, and you will share.
modbus51_c
- modbus RTU 的C51程序 单片机89S52 通信波特率 9600 8位数据 1位停止位 偶校验 485通位接口-Modbus RTU procedures C51 microcontroller communication baud rate 89S52 9600 8-bit data a dual-stop check-bit interface 485
mbus-0.1.2
- MODBUS/TCP to RS-232/485 MODBUS/RTU gateway server
modbus.rar
- 51 modbus源代码，rtu 格式,在c8051f120上实现,51 modbus code ,rtu mode
8051F410_AD_MODBUS
- 本文件是通过485通讯将接受MODBUS指令，采集AD数据，发送出并在对应的LED数码管上十六进制循环显示。-This document will be accepted by 485 MODBUS commands AD data collection, sending out and the corresponding LED digital display on the loop hex.
ModbusMaster
- ModbusMaster.h - Arduino library for communicating with Modbus slaves over RS232/485 (via RTU protocol). This file is part of ModbusMaster. ModbusMaster is free software: you can redistribute it and/or modify it under the terms o
modbusRTU_C51_RS485
- modbus RTU 的C51程序 单片机89S52 通信波特率 9600 8位数据 1位停止位 偶校验 485通位接口 单片机控制板地址 localAddr(变量) 通信可设置数据的地址： 字地址 0 - 255 (只取16位的低8位) 位地址 0 - 255 (只取16位的低8位)-modbus RTU' s C51 program microcontroller 89S52 Communication baud rate 96008 bits of d
zidongfengmen
- 读取P口状态，执行对应的语音程序，并通过485上传数据，ISD1760,modbus，rtu模式。 内含原理图，软件编译器是周立功的-Read the P-port status, perform the corresponding speech program, and upload data through 485, ISD1760, modbus, rtu model. Includes schematics, software compiler weeks meritorious
modbus51
- 基于51的485通讯实现，modbus协议，中断实现方式，具体参数波特率9600，8位，1位结束位，偶校验-Based on 51 485, RTU, modbus protocol checksum, interrupt implementations, the specific parameters of the baud rate of 9600 bits, 1 stop bit, even parity
modbus-rtu
- 485通讯程序，MODUS的源程序，可以直接应用-485 program, the MODUS source code can be applied directly
MODBUS--TCP-RS-232485-MODBUS--RTU
- MODBUS/TCP to RS-232/485 MODBUS/RTU的网关服务器-MODBUS/TCP to RS-232/485 MODBUS/RTU gateway server
[32Bit]ModbusTools.Modbus.Slave.6.2.2.build.871 PatchOnly
- OLE Automation means easy interface to Excel RTU Mode ASCII Mode Modbus TCP/IP Modbus UDP/IP Print and print preview Monitoring of serial data traffic Context sensitive help 10 Display formats such as float, double etc. Adjustable Address Base (0 or
多合一code
- 采用51单片机作为主控制器，通讯方式为485总线，通讯协议为Modbus，波特率为9600，8位数据，1个停止位，无校验位； 本程序作为从机部分编写的；(Using 51 single-chip microcomputer as the main controller, communication mode is 485 bus, communication protocol is Modbus, baud rate is 9600, 8 bit data, 1 stop bits, no pa
PRJV3
- STM8L051F3P6廉价芯片的AD采集和485modbus-RTU通信程序，使用IAR编译。(STM8L051F3P6 cheap chips AD acquisition and 485modbus-RTU communication procedures, using IAR compiler.)
ModBus-Master
- 基于单片机STM32的modbus协议，采用485总线(The Modbus protocol based on single chip microcomputer STM32 adopts 485 bus)
smart_485_单台port0
- MODBUS RTU 485 单台仪表通信取数(The number of MODBUS RTU 485 single meter communication)
STM32_SPI_ADS1118
- 程序使用TI的16位片外ADC采集数据，STM32F103C8T6单片机，485的RTU协议(The program uses 16 bit outside ADC of TI to collect data, STM32F103C8T6 MCU, and 485 RTU protocol)
MODBUS- 485SLAVER
- 本例程为 RS485 MODBUS 主站例程。可以通过按键发送相应的 MODBUS 命令，然后等待从站应答 （或超时）退出等待。 程序使用串口 3（ USART1）与从机通讯，执行结果通过串口 1（ USART1）送到计算机的串口。可以 通过 PC 机的串口终端软件观察程序执行结果(This routine is the RS485 MODBUS master station routine. You can send the corresponding MODBUS commands t
485 Modbus RTU通讯协议
- 485 Modbus RTU通讯协议485 Modbus RTU protocol(485 Modbus RTU protocol)
fx3u rtu
- 三菱 FX3u 作为从站，供上位机直接通过扩展485模块，通过modbus rtu 模式通讯读取数据，寄存器等信息。端口配置程序，9600kps 8 ，1，e格式。(Mitsubishi FX3u serves as slave station for PC to read data, register and other information directly by extending 485 module and communicating in Modbus RTU mode. Port