搜索资源列表
CC2430-LED
- CC2430单片机LED实验,基于zigbee的
IO_CC2430_test
- 包含三个CC2430的I/O测试程序。程序基于IAR软件编写，用来控制片上LED的开关及闪烁。通过适当修改同样可以用于CC1110的开发，估计对开发无线传感器网络的相关人士比较重要。 -CC2430 contains three of the I/O test procedure. Procedures based on the IAR software development, chip used to control the switches and blinking LED. Likewi
cc2430-15
- 在 PC 上从串口向CC2430 发数，即可控制LED 灯的亮灭，控制数据的格式为“灯编号开/关#”，红色LED 编号为1，绿色LED 编号为2，0 是关灯，1 是开灯，如打开红色LED 的命令是“11#”。-In the PC from the serial port to the number of CC2430 can be controlled to eliminate bright LED lights, control the data format for the light n
CC2430-1
- CC2430 基础实验一自动闪烁 本次实验的目的是让用户学会使用 CC2430 的I/0 来控制外设，本例以LED 灯为外设，用 CC2430 控制简单外设时，应将I/O 设置为输出。实验现象是绿色LED 闪烁。-CC2430 lab one
CC2430-2
- CC2430 基础实验二按键控制开关 让用户掌握 CC2430 的按键应用这一常用人机交互方法，本次实用两个分别控制两个LED 灯。-CC2430 lab two
CC2430-3
- CC2430 基础实验三按键控制闪烁 本实验的控制比实验二的控制稍显复杂，这个实验中使用按键控制LED 或闪烁，或熄灭。-cc2430 lab three
CC2430-1
- CC2430 基础实验一LED灯自动闪烁-CC2430 experimental basis for a flashing LED light automatically
CC2430-3
- CC2430 基础实验三 按键控制LED闪烁-CC2430 three buttons to control the basis of experimental LED flashes
CC2430-1
- 学习CC2430的实验例子程序1 自动闪烁 本次实验的目的是让用户学会使用CC2430 的I/0 来控制外设，本例以LED 灯为外设，用 CC2430 控制简单外设时，应将I/O 设置为输出。实验现象是绿色LED 闪烁。-Experimental study and CC2430 automatically flashes example 1 The purpose of this experiment is to let users learn to use the CC2430 t
CC2430-2
- CC2430 基础实验二 按键控制开关 1 实验介绍 让用户掌握CC2430 的按键应用这一常用人机交互方法，本次实用两个分别控制两个LED 灯。-Second, the basis of CC2430 experiment 1 button control switch allows users to grasp the experimental introduction of the key application of this CC2430 HCI commonly used
CC2430-3
- CC2430 基础实验三 按键控制闪烁 1. 实验介绍 本实验的控制比实验二的控制稍显复杂，这个实验中使用按键控制LED 或闪烁，或熄灭。-CC2430 experimental basis for a three-button control of flashing. Experiment introduced in this experiment than in the control of the control of the second experiment a little
CC2430-2
- CC2430 基础实验二按键控制开关 让用户掌握 CC2430 的按键应用这一常用人机交互方法，本次实用两个分别控制两个LED 灯。-CC2430 experimental basis for the Second button control switch allows users to grasp the key CC2430 application of this commonly used method of human-computer interaction, this pr
CC2430-14
- 基于cc2430的在 PC 用串口控制LED，和串口初始化的程序-Cc2430-based PC using the serial port to control the LED, and the serial port initialization process
CC2430-1
- ti公司cc2430的开发板led实验，主要是面向初学者-ti' s cc2430 development board led experiments, mainly for beginners
CC2430UartLed
- cc2430与pc进行串口通信 及 led指示的代码。-cc2430 with the pc serial port communications and led instruction code.
CC2430-4
- CC2430基础实验三，这是定时器T1的使用，通过对LED灯的控制来体现-CC2430-based experiment 3, which is the use of the timer T1, through the control of LED lights to reflect the
1.LED
- zigbee控制led，对初学者很有用，cc2430模块-zigbee control led, very useful for beginners, cc2430 module
CC2430-LED
- CC2430 LED实验源代码，电子科技大学出品-CC2430 LED test source code, University of Electronic Science and Technology produced
CC2430-tickle
- Zigbee CC2430 LED 自动闪烁-Zigbee CC2430 LED automatic flashing
cc2430
- 1.点亮LED灯 2.按键控制 3.外部中断（按键） 4.单片机串口发送数据 5.定时器1 6.ADC单次采样-1 lit LED lights 2. Button control 3 external interrupt (button) 4. Microcontroller serial port to send data 5. Timer 1 6.ADC single sampling