搜索资源列表
led
- ARM LPC2200 定时器中断使用LED闪烁实验-ARM LPC2200 timer LED flashes interrupt the use of experimental
led
- led显示程序，通过定时器中断，可以动态显示数字在数码管上。-led display program, through the timer interrupt, you can dynamically display the figure in the digital control on.
led-int
- 利用单片机的定时器以及中断的方法的LED灯显示程序。-The use of single-chip timer and the method of interruption of LED lights display program.
LED
- DSP2407 发光二极管的程序，中断控制与实现-dsp2407 program for emission of led diode
1111
- ARM的硬件实验，包括中断，led灯，-ARM' s hardware experiments, including the interruption, led lights, and so on
led
- 基本上程序还是DEMO程序,程序并没有采用定时器来生成PWM,而是采用延时循环来实现,这样就做不了其他事情 了,但实际上只需要将主循环转换为定时器中断处理即可,很简单.这个是参照市面上邦定IC RGB控制功能来做的,这应该是采用单片机方案最便宜版本之一了 -Basically the procedure or DEMO program, the program does not use a timer to generate the PWM, instead of using the de
led
- 定时器中断的例程，实现一秒定时，并在led灯上显示- Writes routine which a timer interrupts, realizes one second fixed time, and demonstrated on the led lamp
外部中断实验
- 通过开发板上载有的3个按钮（KEY_UP、KEY0、KEY1），来控制板上的2，LED（DS0和DS1），其中KEY0控制DS0，按一次亮，再按一次，就灭。KEY1控制DS1，效果同KEY0。KEY_UP则同时控制 DS0和DS1，按一次，他们的状态就翻转一次。(Some 3 buttons are uploaded through the development board (KEY_UP, KEY0) (KEY1) to control the 2 LED (DS0 and DS1) on
外部中断实验
- 基于STM32f4107ZGT6开发平台，软件用的是keil，利用外部中断实现led的闪烁(Using external interrupts to achieve LED flashing)
实验5 外部中断实验
- 通过板载的 4 个按键，控制板载的两个 LED 的亮灭以及蜂鸣器的发声(The onboard 4 buttons control the two LED lights on the board and the buzzer sounds)
LED灯 跑马灯
- 8位松瀚单片机，LED跑马灯程序入门，程序结构中断模板(8 Songhan MCU, LED marquee program entry, interrupt program structure template)
实验16.外部中断0控制第一个led
- 外部中断T0点亮一个led，实现中断的控制程序(External interrupt T0 lights up an led to implement the interrupt control program)
STM32 外部中断
- STM32f103vet6进行外部中断，进行led闪烁(STM32f103vet6 for external interrupts and LED flashes)
STM32F107外部中断程序
- 按键触发STM32的GPIO中断，点亮LED(Keystroke triggers GPIO interrupts)
interrupt LED
- 使用DSP28335点亮LED灯，使用中断方式(lighting the LED by DSP28335 with the interrupt mode)
2个按键分别控制2个LED
- 按键S1,S2外部中断方式改变LED1,LED2状态,具有防抖功能(Key S1, S2 external interrupt mode change LED1, LED2 state, with anti - shake function)
STM32定时器中断程序
- 本源代码为讲解基于STM32的定时器中断程序，通过定时器TIM3产生间隔1秒钟一次的中断，在中断中控制LED发光二极管，每次中断都使发光二极管状态取反(This source code is explained based on the STM32 timer interrupt program, through the timer TIM3 interrupt an interval of 1 second, in the interrupt control LED light-emittin
4：STM32_外部按键中断实验
- STM32F10x开发的外部中断应用程序,按键int1和int2控制LED灯(External interrupt applications developed by STM32F10x, key INT1 and INT2 to control the LED lamp)
LED灯外部中断
- 用单片机的外部中断来控制LED灯的亮灭（库函数开发）(External interrupts with the microcontroller to control the LED lights off (library function development))
按键——中断方式
- 通过以中断方式的按键程序来控制单片机上的流水灯的流水方式(Control the flow of water lamp on single chip microcomputer by interrupting the keypad program)