搜索资源列表
buckPWM
- The program is about buck converter PWM in simulink.
buck1
- this is buck inverter with pwm control
Boost_PWM
- Matlab Simulink right boost PWM pulse circuit and the simulation design proce-Matlab Simulink right boost PWM pulse circuit and the simulation design process
buckPWM
- buck circuit PWM simulation, power electronics-buck PWM simulation
20499315buckPWM
- MATLAB buck pwm 用pwm的控制方式实现buck电路-MATLAB buck pwm control method used to achieve buck pwm circuit
Buck_PWM
- BUCK PWM Generation using matlab
Buck
- 降压dc变换器输出功能仿真，根据可控晶闸管调节电压的压降，实现降压电路，采用pwm波控制。-buck DC Converter
28335_mppt
- 4路pwm，buck升压，错相抑制电流脉动-4 pwm, buck boost, current ripple-phase inhibition
buck_close_loop
- There are 3 models of Buck converter closed loops with PWM done in simulink and they work properly
M8_2400
- ATMEGA8_ LTC2400 6位半表头程序 LTC2400最高测量电压为5.3V，超过5.3V或反接都会烧掉。 模拟部分供电最好经过7815稳压，最高输入电压不宜超过18V。 模拟电路与数字电路分开供电。 不要使用开关电源或PWM升压、降压电路供电 -ATMEGA8_ LTC2400 6 ½ -digit meter program LTC2400 highest measured voltage is 5.3V, 5.3V or rev
1.8W-Buck-Topology-Power-Supply-with-VIPer12AS.ra
- This board is an auxiliary power supply based on the VIPer12AS monolithic device with rather low output power required. It is a buck (step-down) converter with a positive output voltage referenced to the common ground based on the monolithic device V
Boost1
- PWM在双向DC-DC的应用时十分显著的，可以用于很多场合，比如电梯节能，电动汽车-PWM convert pwm simulink pwm buckpwm pwm matlab DC DC PWM PI MATLAB PWM buck simulink dc-dc ma pi DC
PWM-motor-control_
- 这是一个Matlab实现的PWM型直流变换器的Simulink仿真，变换方式是Buck-Boost变换方式。示例，提供了一个从5伏到25伏电压，的升压变换。-This is a Matlab Simulink simulation of PWM DC-DC converter, and transform the way Buck-Boost transform. Example, from 5 volts to 25 volts, the boost transformation.
STM32
- 数控直流电源，通过4*4按键输入所需电压，PWM调节BUCK电路的开关管的导通时间调节到你所需的电压-NC DC power supply via 4* 4 keypad enter the desired voltage, PWM BUCK regulator circuit switch conduction time adjusting to your desired voltage
CO2
- 用TI430最小系统开发的瓦斯检测报警器，本设计的特点是节能，间断式检测，休眠期间传感器不供电，检测期间由PWM降压自动为传感器提供稳定的电压，达到节能的效果-Minimum system developed by TI430 gas detection alarm, the characteristics of this design is energy saving, intermittent detection sensor is not powered during the dorman
Buck
- 使用matlab仿真的一个buck降压斩波电路，将带有PI控制器的电路与无PI控制器的电路响应做对比。其中PI控制器采用的是使用S函数编写的控制器，进行简单的修改就可以在仿真中实现专家PI控制等等，控制器的输入参数有Kp，Ki以及控制器输出的上下限定值。因为控制器直接控制的是PWM的脉冲宽度，所以控制器的输出值限定在0到100之间。MySource用来将要求的电压与电源的电压100v进行对比，从而输出相应脉冲宽度的PWM波形给IGBT。-A Buck circuit based on matla
dSPACE Based Implementation of PID Controller for Buck Converter
- In this paper output voltage of chosen buck DC – DC converter is regulated at nominal output voltage of 13 volts under [1] under supply disturbance of 20 to 25 volt and vice versa [2] under load disturbance of 28 to 50 ohms and vice versa. The perfor
PWM
- 基于CCS6.0开发环境，并且基于TMS320F28335平台，一个简单的BUCK闭环程序。 实现了程序的搬移。-Based on CCS6.0 development. and use the TMS320F28335 to achieve a simple buck close-loop program. it also can bring program FLASH to Ram.
BUCK-PID实验
- 使用stm32开发板做的pwm输出控制buck电路，反馈使用PID算法，实现闭环控制(The use of STM32 development board to do PWM output control buck circuit, feedback using PID algorithm to achieve closed-loop control)
BUCK程序
- dcdc电路降压，基于stc12芯片，可通过调整pwm波来控制，步进可调(DCDC buck circuit, based on the STC12 chip, can be controlled by adjusting the PWM wave, adjustable step)