搜索资源列表
uart-edit-EEPROM
- STC12C5204AD单片机通过串口修改EEPROM中数据，先将0x0000扇区数据放入0x0200扇区，然后写入新数据，再将数据读回0x0000扇区,此时只需修改相应的数据，其余的数据无需改动。-STC12C5204AD microcontroller through the serial port to modify the EEPROM data into the first sector data 0x0000 0x0200 sector, and then write the new
STC12C5204AD-Schematic
- STC12C5204AD开发板原理图，pdf格式，没有protel格式的，STC12C5204AD单片机开发的好资料-STC12C5204AD development board schematics, pdf format, no protel format, STC12C5204AD microcontroller development of good information
AD-VoltagePSTC12C5204AD
- STC12C5204AD单片机AD转换程序，使用中位值滤波的方法，结果稳定，精度为0.02V-STC12C5204AD chip AD conversion process, using the median filtering method, the results are stable, precision 0.02V
STC12C5608AD--OK
- STC12C5204AD单片机ad采样输出pwm并将ad的值通过串口发送给上位机，有原理图，-STC12C5204AD SCM ad sample output pwm and ad value to send to the host computer through the serial port schematic
No.29---AD-exchange-STC12C5204AD
- STC12C5204AD开发板上AD转换程序，实现8位电压AD转换，结果显示在1602液晶上，范围为0-5V，将AD转换输出的0-255的数表示为相应的电压值-STC12C5204AD development board AD conversion process to achieve the 8-bit AD converter voltage, the results show in 1602, the range of 0-5V, the AD converter output 0-255
AD
- STC12C5204AD单片机AD转换程序，包含头文件，可以直接调用-STC12C5204AD MCU AD conversion process, include the header file, you can directly call
STC12C5204ADPPWMPP3^7Puart
- STC12C5204AD单片机PWM输出程序，利用自带的PWM输出，即P3.7口输出PWM波，PWm频率为3.6K，可以通过串口来修改PWM波的占空比，PWM输出0-5V，精度为0.1V，在实验板上验证通过。-STC12C5204AD microcontroller PWM output procedures, the use of built-in PWM output, PWM output is P3.7 mouth, PWm frequency is 3.6K, through the
STC12C5204AD
- STC12C5204AD 转换程序-The conversion process STC12C5204AD AD
STC12C5204AD_DSP2812_handle_program
- 基于STC12C5204AD的机器人手柄程序设计，通过该单片机的手柄程序，与DSP2812微处理器通信实现手柄控制机器人运动。-Robot based STC12C5204AD handle programming, through the SCM handle procedures, and the DSP2812 Communication microprocessor to control the robot motion controller.
LVD_check
- STC12系列单片机低压检测的源程序，在STC12C5204AD上试验通过-STC12MCU low voltage detection source, on a test by the STC12C5204AD
ADPEEPROMPmodbus
- STC12C5204AD单片机开发板上实现modbus协议，通过协议可以返回电压转换及lm35获取的温度，并设置PWM占空比，设置EEPROm中数据，06模式支持广播模式，在3块单片机开发板联合的情况下试验通过 -STC12C5204AD microcontroller development boards implement modbus protocol, protocol can be returned by the voltage conversion and lm35 to obt
STC12C5204ADPLEDV1
- STC12C5204AD单片机开发板点亮二极管的程序实例，包含138译码器的使能与控制，是单片机入门很好的学习程序。-STC12C5204AD microcontroller development board light diode instance, contains 138 of the decoder to enable and control, is a good entry-chip learning process.
STC12C5204ADPSTCPLEDPFlicker
- STC12C5204AD单片机控制单个二极管闪烁源代码，二极管由138译码器使能，另一端单片机IO口控制，采用延时程序，是单片机初学者很好的学习源代码-STC12C5204AD flash microcontroller source code to control a single diode, diode 138 by the decoding is enabled, the other end of the single-chip IO port control, using the de
STC12C5204ADPLEDPWater-lamp
- STC12C5204AD单片机上流水灯演示程序，即8个二极管依次点亮，又依次灭掉，演示了程序的执行过程-STC12C5204AD microcontroller demo program on light water, that is eight diodes were lit, in turn exterminate, demonstrates the execution of the program
STC12C5204AD-Development-Board
- STC12C5204AD单片机开发学习系统用户手册，描述了开发办的构成以及部分源码对应的硬件结构图等-STC12C5204AD microcontroller development learning system user manual describes the development office and some source code corresponding to the composition of the hardware structure, etc.
NO.5-LED-display-random-digtial
- STC12C5204AD实验板上数码管静态显示十位任意数字的程序，在实验板上验证通过-STC12C5204AD experimental panel display ten digital still any number of procedures, verified by the experimental board
NO.17-1602--digital-and-Letter
- STC12C5204AD实验板上1602液晶模块字母数字混合显示程序，在开发板上试验通过-STC12C5204AD 1602 breadboard module alphanumeric display program, through the development board test
NO.20-control-buzzer-buzzer
- STC12C5204AD实验板上蜂鸣器蜂音控制 程序，在开发板上试验通过-STC12C5204AD experimental board buzzer buzzer control procedures, testing by the development board
STC12C5204AD
- STC12C5204AD单片机实现PWM调制音频的C语言程序例子-STC12C5204AD MCU PWM modulation audio examples of the C language program
STC12C5204AD-ADC
- STC12C5204AD ADC 单片机adc-STC12C5204AD ADC