搜索资源列表
slaa151
- Interfacing the MSP430 and TMP100 Temperature Sensor
MSP430-TMP100
- MSP430-TMP100数字温度检测系统代码。调试通过的。直接拿来用或者参考。
tmp100
- TMP100数字温度传感器读取源码,可以直接使用,很好的代码
MSP430-I2C
- MSP430单片机413与TMP100的I2C汇编程序。
MSP430IIC
- MSP430与TMP100 I2C温度传感器的接口汇编程序，在ti公司代码的基础上改进，可以直接使用。
fet140_i2c_01
- 演示了如何操作MSP430F149的i2c功能-Descr iption: I2C interface to TMP100 temperature sensor in 9-bit mode. // Timer_A CCR0 interrupt is used as a wake up and to read the upper byte of // the TMP100 temperature register. If the temperature is greater than
MSP430TMP100
- 讲述了msp430与tmp100温度传感器的设计-TMP100
slaa151
- 关于msp430f413用TMP100传感器测量温度的源码-Msp430f413 used on the TMP100 temperature sensor source
slaa151
- 关于msp430f413用TMP100测量温度的电路和说明文档-Msp430f413 used on the TMP100 temperature measurement circuit and documentation
MSP430_TPM100
- MSP430单片机通过片内外设IIC总线，控制温度传感器TMP100的源代码-MSP430 Single-chip-chip peripherals through the IIC bus, TMP100 temperature sensor control the source code
tmp100
- TI tmp100温度芯片驱动代码。是基于STC89C52的代码。-Temperature TI tmp100 code chip driver. The code is based on the STC89C52.
tmp100
- tmp100程序，有多种功能模式选择，在4中模式下有不同的功用。-program for tmp100
TMP100_V1.1
- MSP430f169通过片内自带的I2C模块与温度芯片TMP100通信，并将温度通过LCD12864显示-MSP430f169 through the on-chip built-in I2C module with temperature chip TMP100 communication, and the temperature displayed by LCD12864
Avt3S400A_Eval_MB_I2C_temp_v10_1_00
- This tutorial shows how to use an IIC controller with MicroBlaze. The IIC controller is connected to a Texas Instruments TMP100 temperature sensor. A custom application with code to communicate with the temperature sensor is used to exercise the
fet140_i2c_15
- i2c control for temp sensor tmp1-i2c control for temp sensor tmp100
msp430
- msp430 实验代码 1,MSP430开发基础 2，键盘设计 3，数码管显示电路设计 4，液晶模块接口 5，MSP430 CRC 6，中文输入法 7，数据压缩算法 8，FIR滤波 9，FFT算法 10，波特率自动识别 11,串行存储 12；NAND flash 接口 13；A/ D，TLV2541 14；DA DAC8830 15；ADS1241 16；温度 TMP100 17；定时器 DAC
msp430x22x4_uscib0_i2c
- 温度感应器，利用IIC接口来控制温度和检测-// Descr iption: I2C interface to TMP100 temperature sensor in 9-bit mode. // Timer_A CCR0 interrupt is used to wake up and read the two bytes of // the TMP100 temperature register every 62ms. If the temperature is greate
msp430g2xx3_uscib0_i2c_01
- MSP430通过I2C总线模式跟温度传感器TMP100进行数据通信。当温度达到一定值时，指示灯亮。-MSP430 data communication through the I2C bus mode with temperature sensor TMP100. When the temperature reaches a certain value, the indicator light.
AT89C52--IIC---TMP100
- 给予AT89C52的TMP100--IIc驱动程序-Give AT89C52 TMP100- IIc driver
TMP100
- MSP430F449温度传感器TMP100程序已经调试成功了-MSP430F449 Temperature Sensor TMP100 program