搜索资源列表
buckPWM
- BUCK---PWM电路仿真，包含仿真源程序和仿真搭建的模块，对研究仿真电路的大有裨益。
buckPWM
- The program is about buck converter PWM in simulink.
buck1
- this is buck inverter with pwm control
Boost_PWM
- Matlab Simulink right boost PWM pulse circuit and the simulation design proce-Matlab Simulink right boost PWM pulse circuit and the simulation design process
buckPWM
- buck circuit PWM simulation, power electronics-buck PWM simulation
20499315buckPWM
- MATLAB buck pwm 用pwm的控制方式实现buck电路-MATLAB buck pwm control method used to achieve buck pwm circuit
buckPWM
- buck PWM model for Simulink
Buck_PWM
- BUCK PWM Generation using matlab
HIP6601-6603
- HIP6601是一款非常好用的PWM斩波芯片。电脑主板也是采用这芯片为CPU供电。该文档为HIP6601的器件手册-The HIP6601 and HIP6603 are high frequency, dual MOSFET drivers specifically designed to drive two power N-Channel MOSFETs in a synchronous-rectified buck converter topology. These drive
Buck
- 降压dc变换器输出功能仿真，根据可控晶闸管调节电压的压降，实现降压电路，采用pwm波控制。-buck DC Converter
buck_close_loop
- There are 3 models of Buck converter closed loops with PWM done in simulink and they work properly
1.8W-Buck-Topology-Power-Supply-with-VIPer12AS.ra
- This board is an auxiliary power supply based on the VIPer12AS monolithic device with rather low output power required. It is a buck (step-down) converter with a positive output voltage referenced to the common ground based on the monolithic device V
buckPWM
- Buck PWM controls the firing signal of Buck cnverter.
PWM-motor-control_
- 这是一个Matlab实现的PWM型直流变换器的Simulink仿真，变换方式是Buck-Boost变换方式。示例，提供了一个从5伏到25伏电压，的升压变换。-This is a Matlab Simulink simulation of PWM DC-DC converter, and transform the way Buck-Boost transform. Example, from 5 volts to 25 volts, the boost transformation.
d
- 开关电源 BUCK电路模块 PWM控制与负载过流保护-Switching power supply BUCK PWM control circuit module and the load current protection
Buck_PWM
- buck pwm dc-dc chopper for many usage.
Buck
- 使用matlab仿真的一个buck降压斩波电路，将带有PI控制器的电路与无PI控制器的电路响应做对比。其中PI控制器采用的是使用S函数编写的控制器，进行简单的修改就可以在仿真中实现专家PI控制等等，控制器的输入参数有Kp，Ki以及控制器输出的上下限定值。因为控制器直接控制的是PWM的脉冲宽度，所以控制器的输出值限定在0到100之间。MySource用来将要求的电压与电源的电压100v进行对比，从而输出相应脉冲宽度的PWM波形给IGBT。-A Buck circuit based on matla
BUCK-PID实验
- 使用stm32开发板做的pwm输出控制buck电路，反馈使用PID算法，实现闭环控制(The use of STM32 development board to do PWM output control buck circuit, feedback using PID algorithm to achieve closed-loop control)
BUCK程序
- dcdc电路降压，基于stc12芯片，可通过调整pwm波来控制，步进可调(DCDC buck circuit, based on the STC12 chip, can be controlled by adjusting the PWM wave, adjustable step)
62443
- matlab programming for buck pwm