搜索资源列表
lpc2106飞利浦arm开发版原理图
- 这是一款飞利浦公司的arm芯片的设计的原理图，可以学习到arm的设计特点。-This is a Philips arm of the chip design schematics, can learn to arm design features.
DSP伺服控制开发板原理图
- DSP伺服控制开发板原理图,有丰富的外围接口，可以用来控制伺服电机的工作，-DSP development board servo control diagram with rich peripheral interface can be used to control the servo motor,
STM32 开发板原理图+PCB
- ST公司官方发布的开发板原理图+PCB，PROTEl99格式，可以直接使用，并带有pdf-ST' s official announcement of the development board schematic+ PCB, PROTEl99 format, can be used directly, and with a pdf
完整的控制程序和非常详细步进电机控制原理图
- 完整的控制程序和非常详细步进电机控制原理图，安装PROTEUS后就可以看到仿真的结果,Complete control procedures and a very detailed schematic stepper motor control, the installation can be seen after the PROTEUS simulation results
STLINK_SCHST公司的STM8的仿真器及下载器的原理图
- ST公司的STM8的仿真器及下载器的原理图，目前SWIM的协议还没有公开，协议资料可以去官网上下载相应的技术文档-ST' s STM8 device emulator and download the schematic, the current agreement has not publicly SWIM, protocol information can be downloaded Quguan the appropriate technical documentation
CC2530实现的数据采集模块原理图
- CC2530实现的数据采集模块原理图，能实现多种信号同步采集-CC2530 to achieve data acquisition module schematic, can achieve a variety of signal synchronization acquisition
atmega8-sch.rar
- 这个文件是ATMEGA8的实验板原理图，大家可以下载，在我们公司已经使用，至今效果还可以，大家下载。,This document is ATMEGA8 schematic diagram of the experimental board, everyone can download, in our company have been used and the result also can download the U.S..
ICETEK-VC5509-C.rar
- ICETEK_VC5509_C的硬件原理图，泰瑞公司开发的针对TI C5509A DSP的评估版。包含xilinx FPGA 及语音解码芯片TLV320AIC23等的连接，可借鉴性强 ,ICETEK_VC5509_C hardware schematics, Terry developed for the TI C5509A DSP evaluation version. Contains xilinx FPGA and voice decoder chip TLV320AIC23 conne
EP3C25EVM.rar
- cyclone III EP3C25 开发板原理图,包括flash, sdram, usb, ethernet 等接口电路，可作设计参考。,cyclone III EP3C25 development board schematic diagram, including flash, sdram, usb, ethernet interface circuit, etc., can be used for design.
J-LinkV7_schematic.rar
- J-linkV7版的电路原理图，protel格式，可以直接使用。,J-linkV7 version of the circuit schematic, protel format, can be used directly.
CAN.rar
- 基于CAN总线的电梯控制系统，包括主板程序，子板程序和电路原理图,Based on CAN Bus elevator control system, including the board procedures, sub-board procedures and circuit diagram
Freescale-RS232-CAN
- 用Freescale的8位单片机做的RS232-CAN的通讯转换板.包含固件程序,原理图,PCB图和一个说明文件-Freescale 8-bit microcontroller with the RS232-CAN do protocol conversion board. Contains firmware, schematics, PCB drawings and a descr iption file
can-m16-mcp2515
- 用M16和MCP2515组成的CAN通讯节点。 有原理图和代码-MCP2515 with the composition of M16 and CAN communications nodes. There are schematic and code
crazyflie的原理图和PCB
- crazyflie的原理图和PCBbbbbbbbbbbbbbbb(The quad-rotor is a VTOL multi-rotor aircraft. It is very fit for the kind of reconnaissance mission and monitoring task of near-Earth, so it can be used in a wide range of military and civilian applications. In the d
原理图和PCB源文件
- 该ISP编程器采用ATMEGA8_DIP28作为主控制芯片，预留MOSI，MISO，RET，SCK，VCC，GND。6PIN接口，方便使用者根据需要连接目标板。 同时预留PROGRAMMING编程接口，用户可自行升级下载器固件。(The ISP programmer uses ATMEGA8_DIP28 as the master control chip, reserved for MOSI, MISO, RET, SCK, VCC, GND. 6PIN interface to fac
18KW变频器原理图
- 商用的18KW变频器原理图，可以参考11-18KW通用(Commercial 18KW inverter schematic, you can refer to 11-18KW general)
cpu原理图
- 商用变频器CPU 2406 电路图，可以参考学习(Commercial frequency converter CPU 2406 circuit diagram, you can refer to study)
原理图
- 这个是用STM32F103芯片控制低压无刷直流电机或者永磁同步电机的原理图，可以参考一下(This is the use of STM32F103 chips to control low-voltage brushless DC motor or permanent magnet synchronous motor schematic diagram, you can refer to)
STM32版FX2N源码&原理图(可直接移植)
- FX2N源码V3.8版的使用基本说明： 编译语言：C语言 FX2N源码V3.8版是根据三菱FX2N的PLC通信协议、通信命令以及基于STM32F103系列单片机上编写运行的程序，可以直接利用三菱编程软件编写梯形图下载运行，无需任何转换。 注：1）目前在STM32F103RD/STM32F103VC/STM32F103VD/STM32F103VE/STM32F103ZE测试通过； 2）本程序不完全支持所有梯形图指令，如果需要其他的功能，需要亲自己修改代码， 编译环境：
直流无刷电机控制PCB 原理图 BOM
- 直流无刷电机的控制和驱动，可以使电机正反转。(The control and drive of Brushless DC motor can make the motor rotate forward and backward.)