搜索资源列表
MSP430单片机与L298驱动控制单片机正反转直行后退
- MSP430单片机与L298驱动控制单片机正反转直行后退 基于IAR for MSP430F16X
motor.rar
- 用51单片机实现了直流电机调速，附有PROTEUS仿真电路和PROTEL电路。,51 single-chip microcomputer with a DC motor speed control with PROTEUS circuit simulation circuit and PROTEL.
MOTOR.rar
- msp430控制直流电机，L298驱动，具有正反转，pwm调速功能。,msp430 control of DC motor, L298-driven, with positive inversion, pwm speed control function.
L298
- 基于ARM7的L298驱动程序，芯片L298，控制两个直流电机，没有用PWM调速-Based on ARM7-L298 driver chip L298, control two DC motors, there is no speed control with PWM
L298
- L298驱动直流、步进电机，带有PROTUES仿真-L298-driven DC, stepper motors, with PROTUES simulation
L298
- L298控制直流电机加减速,at89c52控制直流电机加减速-L298 control of DC motor acceleration and deceleration, at89c52 control of DC motor acceleration and deceleration
pwm
- 利用延时产生pwm信号，通过L298功率放大器驱动直流电机- pwm DC-motor
c1
- 直流电机的测速调速模块,运用光电传感器测速,L298芯片调速-DC Motor Speed Control Module, the use of photoelectric sensor gun, L298 chip speed
L298
- 用L298控制直流电机小车，红外对管进行障碍物数据采集，1602液晶显示小车行程。-L298 DC Motor Control with pieces of pipe for obstructions infrared data acquisition, liquid crystal display 1602 vehicle trips.
pwm
- 主要是驱动两个直流电机的程序，通过L298带两个直流电机，稍修改程序即可运用于步进电机。-Drive two DC motors are mainly the procedure, through the L298 with two DC motors, slightly modify the program can be used in stepper motors.
PWMControlMOTOR
- 多功能小车仿真。L298驱动直流电机，有液晶LCD显示方向，速度。-Multi-function car simulation. L298-driven DC motor,there is the direction of liquid crystal LCD display,speed.
DC-motorvelocitymodulation
- 直流电机调速实验C语言程序,使用L298N驱动-DC Motor Speed Experiment C language program, use the L298N drivers
L298n89c51c
- L298控制直流电机加减速的89c51单片机c程序-L298 control of DC motor acceleration and deceleration of the 89c51 microcontroller c program
pwm
- 直流电机驱动芯片采用Ｌ２９８．支流电机驱动就是利用ＰＷＭ脉宽控制Ｌ２９８电流输出大小，从而达到控制电机的目的-Motor Driver IC using L298. Tributaries is the use of motor-driven PWM pulse width control L298 current output size, so as to achieve the purpose of the electrical control-DC motor driver chip L2
DC-motor-driver-program-of-L298
- L298驱动直流电机程序,其中包括正反转-L298 DC Motor Driver Program
L298
- L298直流电机驱动，单片机PWM控制速度-L298 DC motor driver, PWM control chip speed
L298
- 仅仅使用L298驱动芯片，主控为51单片机，在keil中调试测过，专门驱动步进电机的！不是直流电机。-Just use the L298 driver chip, the master microcontroller 51, in keil debugging measured before, specifically to drive stepper motor! Not a DC motor.
L298
- L298控制直流电机，C语言驱动，可直接用于凌阳单片机，亦可改动接口后用于其他单片机-L298 controlled DC motor, C language driver, can be used directly Sunplus can also be used for other changes to the interface chip after
PWM电机 - 副本
- 驱动直流电机，通过l298n来驱动，stm32板拉高引脚PA9与PA10，同时PA7输出PWM值(The drive DC motor is driven by L298N, the STM32 board pulls the high pin PA9 and the PA10, and the PA7 outputs the PWM value)
直流电机速度PID控制
- 光电编码器测得的电机速度反馈信号反馈到单片机中。电机设定速度由ZLG7289模块获得，通过SPI通信传输给单片机。单片机系统根据给定的转速与反馈回来的实际速度相减得出偏差，经过控制算法得出控制量。单片机再把控制量以PWM的形式输出，经过L298功率放大驱动直流电机。ZLG7289模块主要用于显示当前直流电机实际转速和给定转速，并让用户通过键盘输入设定速度。(The motor speed feedback signal measured by the photoelectric encoder