搜索资源列表
main
- 本文件是延时测试程序;LED灯每隔1秒亮1秒 使用外部22.1184MHz晶振, * 应用PLL倍频到100MHZ.
main
- 文件是I2C总线读写测试程序;将跳线器JP6短接,使用外部22.1184MHz晶振. * 功能:定义 0 ~ 9 键为数字键, A ~ F 为功能键。按 A 键后,可按0 ~ 9 数字键, * 从零地址开始存储该键值,并送LED数码管上显示该键值。按 B 键后,从零地 * 址开始读取数据值,并送LED数码管上显示。读取速度每秒一次。按 C 键后, * 停止任何操作。
main
- 本文件是键盘测试子程序;使用外部22.1184MHz晶振.功能:定义16个键为 0 ~ F , * 每按下一个键,蜂鸣器响一声,并在LED数码管上显示相应的字符。
MAIN
- wave公司lab6000实验箱的键盘扫描和led显示程序
main.rar
- MSP430FG4618简单串口通信程序,串口引脚选用P2.4,P2.5通信,并采用P10端口界LED显示字符,MSP430FG4618 simple serial communication procedures, selection of the serial pin P2.4, P2.5 communication and the use of P10 port sector character LED display
main.rar
- 本人用STC12LE5202AD做过的太阳能草坪灯LED充放电控制器,具有浮充,过充,过放,光控+时控等功能, 实际应用良好,希望大家多多指导。,I am done with STC12LE5202AD solar lawn lamp LED charge and discharge controller, with a float, over charge, over discharge, light control+ time control and other functions, th
main.rar
- 使用了EvaTimer1来控制LED灯的亮灭,你在学习中 可通过它来了解EV的定时器工作原理,对以后做电机之类的控 ** 可看到板上8个发光二极管产生流水灯的效果 ,EvaTimer1 to control the use of bright LED lights eliminate, you can study it to understand the EV timer works, right after the class to do motor control board** you
main
- 本次利用液晶扩展板(开发板)两个按键(S6、 S7)分别控制 CC2430 模块两个 LED灯亮灭。 -The use of LCD expansion board (board) two buttons (S6, S7), respectively, control the CC2430 module two LED lights off.
main
- 用定时器 1 来改变小灯的状态,T1 每溢出两次,1 个 LED 灯闪烁,1 个 LED 灯改变当前 状态。 -Timer 1 with small lights to change state, T1 overflow twice each, an LED flashes, an LED light to change the current state.
main-chain.rar
- 单片机C语言编写的LED七彩渐变,带主分控程序,主控发控制信号使各分控同步输出。,C single-chip LED colorful language gradually, with the main sub-control procedures, hair master control signal so that the sub-synchronous output control.
QT-led-test
- 编写一个QT程序以打开一个窗口。窗体中主要有四个指示跑马灯状态的标签和一个控制跑马灯的按钮.步骤指导-Write a QT program to open a window. There are four main forms in the state indicate Marquee Marquee label and a control button Step guide
led
- 主要是显示led的功能,主要是实现反复转换。-Led the main function is to show, is to achieve repeated conversion.
main
- LED闪烁程序 有4个按键四种功能 分别实现不同的闪烁方式-LED flashing process features four buttons, respectively, four different ways of flashing
LED
- 步行小绿人是利用ht1632驱动由6*8*8点阵块组成的24*16LED点阵幕来显示小緑人行走动画。采ht4810a为主芯片来控制进行数据传输, 通过 、 、 &
LEDmain0.3
- 该装置由8块LED、RS-232C等外设构成,内核为H8,具有以下功能。 通过使用RS-232、Xmodem 通讯,进行命令文件的下载功能。 通过8块LED根据命令进行各种模式的显示功能。 -The device consists of 8 LED, RS-232C and other peripheral structure, the kernel for the H8, has the following features.
led
- 基本上程序还是DEMO程序,程序并没有采用定时器来生成PWM,而是采用延时循环来实现,这样就做不了其他事情 了,但实际上只需要将主循环转换为定时器中断处理即可,很简单.这个是参照市面上邦定IC RGB控制功能来做的,这应该是采用单片机方案最便宜版本之一了 -Basically the procedure or DEMO program, the program does not use a timer to generate the PWM, instead of using the de
main
- DSP-f2812 led流水灯实验代码-DSP-f2812
main
- 根据STM32寄存器地址,配置P0~P3为推挽输出,点亮LED灯。(According to the STM32 register address, the configuration P0~P3 is push-pull output, and the LED lamp is lit.)
实验3:LED流水灯
- 这是单片机的LED流水灯的程序代码。其主要内容是C代码。(This is the single chip microcomputer LED water lamp program code.The main content is C code.)
LED驱动
- LED是2~3伏的低电压驱动,必须要设计复杂变换电路,不同用途的LED灯,要配备不同的电源适配器。(The relationship between the forward voltage drop (VF) and the positive current (IF) curve shows that when the forward voltage exceeds a certain threshold (about 2V), that is, the usual conduction vol