搜索资源列表
基于 LPC1114 的 uCOS II Keil MDK 工程模板
- 基于 LPC1114 的 uCOS II Keil MDK 工程模板,其 uC/OS 版本为 V2.54,附 Keil 工程及源代码.
LPC1114_24C02
- nxp lpc1114的IIC的读写程序，已经调试成功，利用keil编译，flashmagic烧写程序-nxp lpc1114 of the IIC' s literacy program has been successful debugging using keil compiler, flashmagic programming procedures
KEILBASEDMATIXKEY
- 基于KEIL LPC1114 的矩阵键盘扫描程序，C语言描述，简单实用。-KEIL LPC1114-based matrix keyboard scanner, C language descr iption of simple and practical.
MATRIXjianpan
- 基于KEIL LPC1114 的矩阵键盘扫描程序，C语言描述，简单实用。-KEIL LPC1114-based matrix keyboard scanner, C language descr iption of simple and practical.
LPC1114
- LPC11系列开发软件包，包含所有资源。-LPC11 series of development packages, including all of the resources.
LPC11xx_CAN.104
- LPC1114单片机的CAN总线通讯例程,开发环境为Keil C编译器-LPC11xx microcontroller CAN bus communication routine, Keil C compiler
LPC11xx_Sample
- LPC1114单片机内部功能模块的应用示例,Keil C编译器的-LPC1114 microcontroller modules within the application example, Keil C compiler
code.bundle.lpc11xx.keil
- These are the examples of LPC1114 microcontroller,Microcontroller produced by NXP, founded by Phillips. These examples show many simple code that can be run in Keil software. The examples include: ADC, Blinky LED, gpio, i2c, i2c slave, pwm, rs485, CA
GPIO_OUT
- This example of LPC1114 code that can be run in Keil Software, the microcontroller produced by NXP, found by Phillips semiconductor. This example show how to set output in LPC1114.The source code of LPC1114 is rarely uploaded, so here I share the sou
2.0---UART
- ARM处理器UART通信 环境Keil 处理器NXP LPC1114-ARM processor UART communication
DSl8B20PLPC1114PTFT
- 软件 keil 平台 LPC1114 传感器 DS18B20 显示 240*320的TFT彩色液晶 测试已经通过。-Drive the DS18B20 on the LPC1114, and 240* 320 TFT color LCD display the appropriate information.
LCD1602
- 基于KEIL环境的LPC1114单片机4位并行LCD1602驱动程序，自己整理，有详细注解。-KEIL environment LPC1114 microcontroller-based four parallel LCD1602 driver, finishing, detailed notes.
LM75_AT24C04(Simulation-of-IIC-port)
- 采用LPC1114主芯片的LM75和AT24C01的控制，精华之处是共用同一端口，但在设计产品时，增加了很多的外设，共用IIC端口很容易出现读写错误，因此本人花了精力设计出本代码的在共用IIC线上，两种不同的IIC处理方法，在产品上非常成功，不敢独享，特此给大家参考，编译环境：keil mdk453-Using LPC1114 main chip LM75 and AT24C01 control, the essence is that share the same port, but in t
Cortex-M0_for_lpc1100--uCOS-II
- LPC1114支持ucos II系统的软件，使用keil编译。-LPC1114 support ucos II OS, use keil to compile the code
LPC1114ChipRS485Drive
- RS485通信程序，开发工具:Keil uVision4,开发环境:LPC1114单片机，改一下管脚定义，就可使用。-RS485 communication procedures, development tools, Keil uVision4, development environment: LPC1114 microcontroller, change the pin definition, can be used.
E931.96
- 本文档基于 E931.96 运动检测控制器和 LHI968 被动红外探头设计被动红外，采用的板 子为 ZLG APL_PIR V1.00，控制器为 LPC1114，开发环境为 Keil。-This document is designed based on a passive infrared motion detection controller E931.96 and LHI968 passive infrared sensor, using the board as ZLG APL_P
Control-stepper-by-NRF2401
- 本源程序可在Keil U5下运行或修改。单片机采用 瑞生 LPC1114； 上位机（PC）发出 02080000，通过NRF2401无线模块发送； 单片机接收后通过端口P1.9+P1.5发出相应个脉冲。将2端口并起来，接至步进驱动器pulse端，电机转动80000个脉冲。其他功能详见源程序。-The sourcecodes run in Keil 5.Transmision betwen PC and LPC1114 by NRF2401 wireless module.