搜索资源列表
FIST
- 用于PC机与光电编码盘进行通讯部分的下位机，驱动部分程序-for PC and optical encoder disk communications part of the next crew, driving some of the procedures
fpga_coder_module
- 本人编写的FPGA光电编码器输入模块,没有实验,但仿真基本实现,希望有参考价值.-FPGA optical encoder input module, there is no experimental, but simulation technology, hope to have reference value.
fhe-pulse
- 光电编码器采集脉冲的程序，采用计数查询等待中断方式， 液晶显示正反转 ,显示脉冲数（60个/转），显示转圈数-optical encoder pulse acquisition procedures adopted count inquiries pending interruption, LCD rotating direction Pulse a few shows (60 / switch), the show moved around a few
MCU2PID
- 使用ICCAVR编辑，配合MCU1使用。 主要进行了增量式光电编码器的脉冲读取，PID控制-use ICCAVR editors, with MCU1 use. A major incremental optical encoder pulse reading, PID control
v_pid
- 使用ICCAVR编辑，配合MCU1使用。 主要进行了增量式光电编码器的脉冲读取，PID控制的头文件-use ICCAVR editors, with MCU1 use. A major incremental optical encoder pulse reading, PID control of the header files
ShaftEncoder
- 电机的测速中需要使用到光电编码盘,如果是自己制作光电编码盘,就要该旋转编码盘打印程序-Motor guns need to use optical encoder disk, if it is to produce their own optical encoder disk, it is necessary to set the rotary encoder Print
zhuanpan.rar
- 增量式光电编码器输出四分频脉冲计数，分别为A，B两路信号,Incremental optical encoder pulse count output frequency of a quarter, namely A, B two-way signal
coder_counter
- 增量式光电编码器计数器的FPGA实现程序,verilog3段式FSM,异步加载.-Incremental Optical Encoder counter program FPGA implementation, verilog3 struts FSM, asynchronous load.
ZLJISHUQI
- 】文中重点讨论基于单片机的光电脉冲编码器计数器的软件倍频和辨向原理,并从编码 盘条纹和位置检测元件的空间分布原理出发给出了在编码器输出A、B 正交方波的前提下最多只 能4 倍频的结论,最后介绍了集倍频、辨向、计数于一体的单片机计数器原理,该计数器具有消除抖 动误计数、倍频数可选、计数长度无限制的特点-】 The article focused on single-chip-based optical pulse encoder software counter to the prin
H2_3
- 这是光电编码器的汇编程序，希望对学习的人有帮助-This is a compilation of optical encoder procedures, and they hope to learn helpful
statemachine
- 基于状态图的光电编码器4倍频vhdl程序，输入相位差90度的两相，输出倍频和方向信号-Based on the state of the optical encoder Figure 4 multiplier vhdl procedure, enter a 90-degree phase difference of two-phase, frequency and direction of the output signal
Automatic landing system can be remote control led bannerd
- 全自动可遥控旗帜升降系统以AVR单片机为核心，由PWM对电机进行变频调速，高精度光电编码器测速，闭环式电路控制。能够利用按键输入相应的指令控制旗帜的升降，还可以实现在特定位置停留的功能。利用LCD可以显示旗帜的实时高度和相应的控制命令，用LED指示旗帜是否处于半旗状态，具有语音提示报警功能，并可利用无线模块实现遥控功能，准确均匀地实现旗帜的升降-Automatic landing system can be remote-controlled flag to AVR microcontrolle
STCPS2
- 51光电编码器实现，STC处理编码器的要求，同时编码根据PS/2协议，实现上下键以及确定键。-Optical encoder 51 to achieve, STC encoder processing requirements, as well as coding in accordance with PS/2 protocol, to achieve and to identify the key up and down keys.
52250440605_AB
- 基于CPLD 的光电脉冲码盘 信号四倍频电路设计-CPLD-based electro-optical pulse encoder signals four multiplier circuit design
quadrature
- The output from incremental optical encoders and from many other types of measurement devices is known as a “quadrature” signal. A quadrature signal consists of two square waves 90° out of phase. The input channel on our encoder interface board count
全自动可遥控旗帜升降系统
- 全自动可遥控旗帜升降系统以AVR单片机为核心，由PWM对电机进行变频调速，高精度光电编码器测速，闭环式电路控制。能够利用按键输入相应的指令控制旗帜的升降，还可以实现在特定位置停留的功能。利用LCD可以显示旗帜的实时高度和相应的控制命令，用LED指示旗帜是否处于半旗状态，具有语音提示报警功能，并可利用无线模块实现遥控功能，准确均匀地实现旗帜的升降。-Fully automatic remote control system to lift the banner of AVR microcontro
optical-encoder
- 此为51 8位单片机16 位置旋转编码器的源码，自己编的，keilc 环境下编译，保证能用，编码开关为红外机械式连续旋转。-51 cpu optical source code，16 position
encoder
- 使用VHDL编写的光电编码器。并且在quartus软件进行仿真。最终下载在FPGA板上实现光电编码器的使用。-Optical encoder using VHDL written. And quartus software simulation. The final use of photoelectric encoder download FPGA board.
Atmega8-and-encoder
- Code for an optical encoder with the use of a microcontroller atmega8, with RS232 serial communication with a PC.
encoder-c51-program
- IAR 编译器下 51单片机 读取4000线 光学编码器程序-IAR compiler under the 4000 single chip to read 51 wire optical encoder program