搜索资源列表
new__arm7_armboot-1.1.0
- 多种Arm7/9单片机的 的嵌入式系统UCOS代码，具有RS232串口，TCP/IP网络，TFTP, USB接口代码，非常完整-variety of Arm7 / 9 MCU embedded systems UCOS code, with RS232 serial port, TCP / IP network, TFTP, USB interface code, a very complete
sshtools-j2ssh-0[1].0.2-alpha-src
- Sshtools 是一个纯Java实现的SSH2协议，提供了底层传输，认证和连接协议，高层协议有会话，远程命令执行，文件传输和端口前递-Sshtools is a pure Java Implementation of SSH2 agreement to provide the underlying transmission, authentication and access agreements and high-level agreement conversation, remote co
gcomm-1.0.tar
- Gcomm is a serial communications program similar to seyon, but more modern, and easier to use. Works over serial port, via TCP/IP, or a pipe through another program. Supports xmodem/ymodem/zmodem protocols. Visit the gcomm.sourceforge.net home page f
gsms-1.0
- This a c++ program in MFC. Including the basic function to send and receive msg, connection to serial port, and PDU format. -This a c program in MFC. Including the bas ic function to send and receive msg, connection to serial port, and PDU format.
ex4-1
- 这是一个有关单片机C语言使用的范例，这个范例说明如何使用 Port 1 输出跑马灯
uCOS-II_MSP430F1132
- 精選一個 uC/OS-II Porting 於一般業界使用之 MSP430F1132 開發板上任務調度的例程,於 app.c 內建構了一個可於此開發板上 Port 1.0 驅動 LED 閃爍任務工程,全例程於 IAR MSP430 V3.42A 下編譯,同時亦將此工程設好斷點可方便於 Simulator 內直接觀測 uC/OS 任務調度狀態.
hub4com-1.1.0.0
- 从一个串口接收到的数据广播到其他串口，用于串口调试、协议分析、多个程序共享GPS端口等场合。It allows to send data received from one COM port to a number of COM ports and vice versa. In conjunction with the com0com driver the hub4com makes it possible to handle data from a single serial devi
fprobe-1.0.2
- 模仿cisco路由器，产生netflow，送到指定的收集器上，以相对低廉的软件代价来实现昂贵的路由器的功能 fprobe -i eth0 -l 3 host:port-imitate, have netflow sent to a designated collection device, a relatively low cost of the software to achieve expensive routers function fprobe-i eth0-l three host :
uCOS-III-Port-STM32F2XX.1.0.1
- uCOS-III Port STM32F2-uCOS-III Port STM32F2XX
xvidcore-1.0.0-port.for.symbia
- xvidcore的Symbian移植版，版本1.0.0,xvidcore 1.0.0 port for symbian
usbmgr-1.0.0.tar.gz
- usb端口管理程序，可以监控usb口使用情况并控制接入设备的数据,usb port management procedures to monitor the use of usb port and control access to equipment data
spi_V1.0.3
- //说 明：msp430通过模拟的spi驱动flash W25X32 //描 述：用于主函数中直接调用 flash写函数 写入数据 //功 能：写入flash 一个字节数据 flash地址自动加一 //端 口：p7.0 接/CS片选端 , p7.1用于时序脉冲, p7.2 用作MOSI主机输出从机输入 ， // p7.3用作MISO主机输入从机输出, // p1.4接/WP写保护引脚 ，此程序里没有用到 所以直接拉高，不用。 // 也可以连写 都试过了
link_port-v1[1].1.0
- 用于测试ADI的TS201与FPGA之间通信的LINK程序，压缩文件内包括VHDL和Verlog代码。-ADI is used to test the communication between the TS201 and the FPGA' s LINK program, compressed file to include VHDL and Verlog code.
jWebSocketServer-1.0-nb20105
- jWebSocket Server - 基于Java的WebSocket服务器，用于server-to-client(S2C)客户端到服务器的流媒体解决方案，和服务器控制(C2C) client-to-client客户端到客户端的通信。-Archive (.zip) with all required .jar files and libraries to run the jWebSocket Server including an example configuration file (~26
s7200
- 默认串口1，V区操作 注意：操作VW时，地址应为偶数 plc参数：波特率9600，偶效验，8数据位，1停止位 此程序工控爱好者交流使用， qq: 57476662 email: lkl_xz@163.com -The default serial port 1, V District operations Note: The operation of VW, the address should be an even plc parameters: 9600 baud,
advairtizerv10
- uIP 1.0 在 NXP LPC2148 ARM7 上的移植-A port of uIP 1.0 to NXP LPC2148 ARM7 plus PIC enc28j60 ethernet controller, and LCD Color Display, is available at Braintechnology
SPE-0[1].8.3.c-wx2.6.1.0-no_setup
- Serial port comm file s. Tried to to do it but could not make it working.p[lease help
com0com-2.2.1.0
- 虚拟串口驱动代码，可以虚拟多个串口，供测试时使用-Virtual serial port driver code
110Port1.0
- 并口示波器模拟程序，对接口编程和仪器控制有需要的人员可以参考。-Parallel port oscilloscope simulation procedures, programming and instrument control interface, there is a need for personnel for reference.
ST32-UART-serial-port-1-Printf
- UART串口1 Printf(STM32神舟III号-库函数版)-UART serial port 1 Printf (STM32 Shenzhou III numbers- library function version)