搜索资源列表
ccutest3
- 功能：使用CCU的4个模块，实现非对称PWM输出。 说明：将跳线器J5、J6、J27取出，J3短接到OCD端，在JP6的PWM1、PWM2、PWM3 分别测试模块A、B、C的输出，DAOUT是模块D输出经漏波后的电压。 通过跳线器J8、J9选择高频晶振6MHz。 -function : the use of CCU's four modules, achieving non-symmetric PWM output. Note : All of the jumpe
pwm3-ac-ctrl-motor-0_0_6
- avr atmega frimily 使用PWM控制交流电机，加入零点检测，防止在去磁过程中灌通上下桥而烧毁功率管。-avr atmega frimily use PWM control AC motors, to 0.1 detection, to prevent the magnetic process via next bridge burning power management.
pwm3-ac-ctrl-motor-0_0_3
- DSP实现三相异步电机矢量控制的C语言算法-DSP realization of three-phase induction motor vector control algorithm for the C language
1
- PWM电机控制代码,由pwm2,pwm3控制.-PWM motor control code, from pwm2, pwm3 control.
pwm3-ac-ctrl-motor-0_0_3
- ADC for AVR controller
pwm3-ac-ctrl-motor-0_0_3
- Atmel PWM control 3 phase ID motor
PWM3
- 用Keil c开发的51单片机产生pwm代码，使用时只需根据单片机类型改变头文件类型即可，代码已经过验证没有问题。-51 developed by Keil c generate pwm microcontroller code, when used only under the SCM type of file types can change the header, the code has been verified there is no problem.
PWM3
- 双极性PWM整流,整流结果电流电压同相位-Bipolar PWM rectifier
PWM8
- 在C8051F336开发板上，实现了PWM3通道的控制，可实现占空比的设置，周期的设置。-In C8051F336 development board, realize the PWM3 channel control, can realize the duty ratio setting, cycle set
MyPWM
- 为TI的LM3S系列的PWM输出例程：在PH0/PWM2和PH1/PWM3管脚产生占空比不同的PWM方波-TI LM3S series PWM output routines: in PH0/PWM2 and PH1/PWM3 pin duty cycle of the PWM square wave
STEP
- DSP控制步进电机原理 由DSP输出的PWM3~6做为步进电机的4个信号线输入,选了PWM的IO口.-DSP controlled stepper motor principle by the DSP output for PWM3 ~~ four signal line input as a stepper motor, select the IO port of the PWM.
TMS320F28335_PWM_duli
- 针对TI公司TMS320F28335的ePWM模块开发出的程序。该程序使得PWM3、PWM4、PWM5共三组六个通道输出相互独立的PWM。-TI' s TMS320F28335 ePWM module development program. The program makes PWM3, the three groups PWM4, PWM5 six channels of output mutually independent PWM.
pwm3
- 用kevi4 写的pwm控制程序，六个按键控制三个pwm加减-The wrote pwm control procedures with kevi4 six button control three pwm subtraction
PWM1234
- 此程序功能为让 PWM1 PWM3 PWM7 PWM9 独立输出不同占空比的PWM。 程序设置全在DSP281x_Ev.c 函数里。 -This program features to allow independent output PWM1 PWM3 PWM7 PWM9 different duty cycle PWM. Program settings all in DSP281x_Ev.c function inside.
4PWM-and-Key
- MSP430F169 四路互补PWM波，PWM1与PWM2互补，PWM3与PWM4互补，占空比可调。-MSP430F169 four complementary PWM wave, PWM1 and PWM2 complementary, PWM3 and PWM4 complementary variable duty cycle.
xiaoche1
- 这是电机pwm，调试驱动程序，适用于STC12c56系列单片机，记得分清PWM0,PWM3，PWM1,PWM2分别控制左右两路电机。-This is the motor pwm, debugging drivers for STC12c56 series microcontroller, remember to distinguish PWM0, PWM3, PWM1, PWM2 about two separately controlled motor.
pwm3
- 现代单片机的pwm程序，能够改变脉宽和周期！-Modern microcontroller pwm program that can change the width and cycle!
dsp
- Pwm输出信号的设计 试设计四路（PWM1,PWM2,PWM3,PWM4）输出，载波频率为8ms，波形关系如图所示（一个周期）： -Design test design four (PWM1, PWM2, PWM3, PWM4) output Pwm output signal carrier frequency of 8ms, waveform relationship shown in Figure (a period):
PWM2-PWM3
- STC15W4K32S4系列单片机有6路高精度PWM，即PWM2、PWM3 、PWM4 、PWM5 、PWM6、PWM7。PWM波形发生器为每路PWM又设计了两个用于控制波形翻转的计数器T1和T2，可以非常灵活的控制每路PWM的高电平和低电平的宽度，实现对PWM占空比及PWM输出延迟进行控制。(STC15W4K32S4 series microcontroller has 6 high precision PWM, that is, PWM2, PWM3, PWM4, PWM5, PWM6, P
pwm3-ac-ctrl-motor-0_0_6
- atmel pwm3, sample code